inetd(8N) — UTek W2.3



INETD(8N)               COMMAND REFERENCE               INETD(8N)



NAME
     inetd - internet ``super-server''

SYNOPSIS
     /etc/inetd [ -d ] [ configuration file ]

DESCRIPTION
     Inetd should be run at boot time by /etc/rc.local.  It then
     listens for connections on certain internet sockets.  When a
     connection is found on one of its sockets, it decides what
     service the socket corresponds to, and invokes a program to
     service the request.  After the program is finished, it
     continues to listen on the socket (except in some cases
     which will be described below).  Essentially, inetd allows
     running one daemon to invoke several others, reducing load
     on the system.

     Upon execution, inetd reads its configuration information
     from a configuration file which, by default, is
     /etc/inetd.conf.  There must be an entry for each field of
     the configuration file, with entries for each field
     separated by a tab or a space.  Comments are denoted by a
     ``#'' at the beginning of a line.  There must be an entry
     for each field.  The fields of the configuration file are as
     follows:
          service name
          socket type
          protocol
          wait/nowait
          user
          server program
          server program arguments

     The service name entry is the name of a valid service in the
     file /etc/services/.  For ``internal'' services (discussed
     below), the service name must be the official name of the
     service (that is, the left-most entry in /etc/services).

     The socket type should be one of ``stream'', ``dgram'',
     ``raw'', ``rdm'', or ``seqpacket'', depending on whether the
     socket is a stream, datagram, raw, reliably delivered
     message, or sequenced packet socket.

     The protocol must be a valid protocol as given in
     /etc/protocols.  Examples might be ``tcp'' or ``udp''.

     The wait/nowait entry is applicable to datagram sockets only
     (other sockets should have a ``nowait'' entry in this
     space).  If a datagram server connects to its peer, freeing
     the socket so inetd can received further messages on the
     socket, it is said to be a ``multi-threaded'' server, and
     should use the ``nowait'' entry.  For datagram servers which



Printed 10/17/86                                                1



INETD(8N)               COMMAND REFERENCE               INETD(8N)



     process all incoming datagrams on a socket and eventually
     time out, the server is said to be ``single-threaded'' and
     should use a ``wait'' entry.  ``Tftp'' and ``talk'' are both
     examples of the latter type of datagram server.

     The user entry should contain the user name of the user as
     whom the server should run.  This allows for servers to be
     given less permission than root.  The server program entry
     should contain the pathname of the program which is to be
     executed by inetd when a request is found on its socket.

     The arguments to the server program should be just as they
     normally are, starting with argv[0], which is the name of
     the program.  If the service is provided internally, the
     word ``internal'' should take the place of this entry.

CAVEATS
     The number of servers is limited to 26.  The max number of
     arguments to a server is limited to 64.

SEE ALSO
     services(5n), ftpd(8n), rexecd(8n), rlogind(8n), rshd(8n),
     syslogd(8n), telnetd(8n), tftpd(8n).
































Printed 10/17/86                                                2

%%index%%
na:72,69;
sy:141,176;
de:317,2434;2895,859;
ca:3754,160;
se:3914,314;
%%index%%000000000103

Museum

Related Articles