ROUTED(8N) COMMAND REFERENCE ROUTED(8N) NAME routed - network routing daemon SYNOPSIS /etc/routed [ -s ] [ -q ] [ -t ] [ logfile ] DESCRIPTION Routed is invoked at boot time to manage the network routing tables. The routing daemon uses a variant of the Xerox NS Routing Information Protocol in maintaining up to date kernel routing table entries. In normal operation routed listens on udp(4n) socket 520 (decimal) for routing information packets. If the host is an internetwork router, it periodically supplies copies of its routing tables to any directly connected hosts and networks. When routed is started, it uses the SIOCGIFCONF ioctl to find those directly connected interfaces configured into the system and marked ``up'' (the software loopback interface is ignored). If multiple interfaces are present, it is assumed the host will forward packets between networks. Routed then transmits a request packet on each interface (using a broadcast packet if the interface supports it) and enters a loop, listening for request and response packets from other hosts. When a request packet is received, routed formulates a reply based on the information maintained in its internal tables. The response packet generated contains a list of known routes, each marked with a ``hop count'' metric (a count of 16, or greater, is considered ``infinite''). The metric associated with each route returned provides a metric relative to the sender. Response packets received by routed are used to update the routing tables if one of the following conditions is satisfied: 1.No routing table entry exists for the destination network or host, and the metric indicates the destination is ``reachable'' (i.e. the hop count is not infinite). 2.The source host of the packet is the same as the router in the existing routing table entry. That is, updated information is being received from the very internetwork router through which packets for the destination are being routed. 3.The existing entry in the routing table has not been Printed 5/12/88 1
ROUTED(8N) COMMAND REFERENCE ROUTED(8N) updated for some time (defined to be 90 seconds) and the route is at least as cost effective as the current route. 4.The new route describes a shorter route to the destination than the one currently stored in the routing tables; the metric of the new route is compared against the one stored in the table to decide this. When an update is applied, routed records the change in its internal tables and generates a response packet to all directly connected hosts and networks. Routed waits a short period of time (no more than 30 seconds) before modifying the kernel's routing tables to allow possible unstable situations to settle. In addition to processing incoming packets, routed also periodically checks the routing table entries. If an entry has not been updated for 3 minutes, the entry's metric is set to infinity and marked for deletion. Deletions are delayed an additional 60 seconds to insure the invalidation is propagated throughout the internet. Hosts acting as internetwork routers gratuitously supply their routing tables every 30 seconds to all directly connected hosts and networks. In addition to the facilities described above, routed supports the notion of ``distant'' passive and active gateways. When routed is started up, it reads the file /etc/gateways to find gateways which may not be identified using the SIOGIFCONF ioctl. Gateways specified in this manner should be marked passive if they are not expected to exchange routing information, while gateways marked active should be willing to exchange routing information (i.e. they should have a routed process running on the machine). Passive gateways are maintained in the routing tables forever and information regarding their existence is included in any routing information transmitted. Active gateways are treated equally to network interfaces. Routing information is distributed to the gateway and if no routing information is received for a period of the time, the associated route is deleted. The /etc/gateways is comprised of a series of lines, each in the following format: < net | host > name1 gateway name2 metric value < passive | active > The net or host keyword indicates if the route is to a network or specific host. Printed 5/12/88 2
ROUTED(8N) COMMAND REFERENCE ROUTED(8N) Name1 is the name of the destination network or host. This may be a symbolic name located in /etc/networks or /etc/hosts, or an Internet address specified in ``dot'' notation; see inet(3n). Name2 is the name or address of the gateway to which messages should be forwarded. Value is a metric indicating the hop count to the destination host or network. The keyword passive or active indicates if the gateway should be treated as passive or active (as described above). OPTIONS -s This option forces routed to supply routing information whether it is acting as an internetwork router or not. -q This option is the opposite of the -s option. -t This option causes, all packets sent or received to be printed on the standard output. In addition, routed will not divorce itself from the controlling terminal so that interrupts from the keyboard will kill the process. logfile Any other argument supplied is interpreted as the name of the file in which routed's actions should be logged. This log contains information about any changes to the routing tables and a history of recent messages sent and received which are related to the changed route. FILES /etc/gateways for distant gateways RETURN VALUE [0] Routed is running. [1] Routed is not running. [-1] No action taken. CAVEATS The kernel's routing tables may not correspond to those of routed for short periods of time while processes utilizing existing routes exit; the only remedy for this is to place the routing process in the kernel. SEE ALSO udp(4n). Printed 5/12/88 3
%%index%% na:312,83; sy:395,324; de:719,3129;4232,3453;8069,759; op:8828,1150; fi:9978,137; rv:10115,371; ca:10486,371; se:10857,103; %%index%%000000000157