NAME

netstat − show network status

SYNOPSIS

netstat [ −Aan ] [ −f address_family ] [ system ] [ core ]
netstat [ −imnrs [ [ −f address_family ] [ system ] [ core ]
netstat [ −n ] [ −I interface ] interval [ system ] [ core ]

DESCRIPTION

The netstat command symbolically displays the contents of various network-related data structures.  There are a number of output formats, depending on the options for the information presented.  The first form of the command displays a list of active sockets for each protocol.  The second form presents the contents of one of the other network data structures, according to the option selected.  Using the third form, with an interval specified, netstat will continuously display the information regarding packet traffic on the configured network ­interfaces. 

The options have the following meanings:

−A With the default display, show the address of any protocol control blocks associated with sockets; used for debugging. 

−a With the default display, show the state of all sockets; normally sockets used by server processes are not shown. 

−i Show the state of interfaces that have been configured. 

−I interface
Show information only about this interface; used with an interval as described below. 

−m Show statistics recorded by the memory management routines (the network manages a private pool of memory buffers). 

−n Show network addresses as numbers (normally netstat interprets addresses and attempts to display them symbolically).  This option may be used with any of the display formats. 

−s Show per-protocol statistics. 

−r Show the routing tables.  When −s is also present, show routing statistics instead. 

−f address_family
Limit statistics or address control block reports to those of the specified address family. The following address families are recognized: inet, for AF_INET. 

The arguments, system and core allow substitutes for the defaults /unix and /dev/kmem. 

The default display, for active sockets, shows the local and remote addresses, send and receive queue sizes (in bytes), protocol, and the internal state of the protocol.  Address formats are of the form host.port or network.port if a socket’s address specifies a network but no specific host address.  When known, the host and network addresses are displayed symbolically according to the databases /etc/hosts and /etc/networks, respectively.  If a symbolic name for an address is unknown, or if the −n option is specified, the address is printed numerically, according to the address family.  For more information regarding the Internet “dot format,” refer to inet(3I). Unspecified, or “wildcard,” addresses and ports appear as ∗. 

The interface display provides a table of cumulative statistics regarding transferred packets, errors, and collisions.  The network addresses of the interface and the maximum transmission unit (“mtu”) are also displayed. 

The routing table display indicates the available routes and the status of each.  Each route consists of a destination host or network and a gateway to use in forwarding packets.  The flags field shows the state of the route (U if up), whether the route is to a gateway (G), and whether the route was created dynamically by a redirect (D).  Direct routes are created for each interface attached to the local host; the gateway field for such entries shows the address of the outgoing interface.  The refcnt field gives the current number of active uses of the route.  Connection-oriented protocols normally hold on to a single route for the duration of a connection while connectionless protocols obtain a route while sending to the same destination.  The use field provides a count of the number of packets sent using that route.  The interface entry indicates the network interface utilized for the route. 

When netstat is invoked with an interval argument, it displays a running count of statistics related to network interfaces.  This display consists of a column for the primary interface (the first interface found during network setup) and a column summarizing information for all interfaces.  The primary interface may be replaced with another interface with the −I option.  The first line of each screen of information contains a summary since the system was last rebooted.  Subsequent lines of output show values accumulated over the preceding interval. 

The memory usage display provides information on STREAMS resources including buffers, streams and queues.  It is organized in six columns with the first being the name of the resource and the remaining five have the following meanings:

alloc how many of the resource were allocated at configuration time. 

inuse how many of the resource are in use at the moment. 

total how many of the resource have been allocated since boot time. 

max the maximum number of the resource that have been allocated at the same time. 

fail the number of times an attempt to allocate the resource failed for any reason. 

SEE ALSO

trpt(1M), inet(3I), hosts(5), networks(5), protocols(5), services(5). 

BUGS

The notion of errors is ill-defined. 

Only those network interfaces implementing the DLGSTAT ioctl display counts. 

\*U  —  Version 1.0