terminfo(4) FILE FORMATS terminfo(4)
NAME
terminfo - terminal capability data base
SYNOPSIS
/usr/share/lib/terminfo/?/*
DESCRIPTION
terminfo is a database produced by tic that describes the
capabilities of devices such as terminals and printers.
Devices are described in terminfo source files by specifying
a set of capabilities, by quantifying certain aspects of the
device, and by specifying character sequences that effect
particular results. This database is often used by screen
oriented applications such as vi and curses programs, as
well as by some UNIX system commands such as ls and more.
This usage allows them to work with a variety of devices
without changes to the programs.
terminfo source files consist of one or more device descrip-
tions. Each description consists of a header (beginning in
column 1) and one or more lines that list the features for
that particular device. Every line in a terminfo source
file must end in a comma (,). Every line in a terminfo
source file except the header must be indented with one or
more white spaces (either spaces or tabs).
Entries in terminfo source files consist of a number of
comma-separated fields. White space after each comma is
ignored. Embedded commas must be escaped by using a
backslash. The following example shows the format of a ter-
minfo source file.
alias1 | alias2 | ... | aliasn | longname,
<white space> am, lines #24,
<white space> home=\Eeh,
The first line, commonly referred to as the header line,
must begin in column one and must contain at least two
aliases separated by vertical bars. The last field in the
header line must be the long name of the device and it may
contain any string. Alias names must be unique in the ter-
minfo database and they must conform to UNIX system file
naming conventions [see tic(1M)]; they cannot, for example,
contain white space or slashes. Every device must be
assigned a name, such as "vt100". Device names (except the
long name) should be chosen using the following conventions.
The name should not contain hyphens because hyphens are
reserved for use when adding suffixes that indicate special
modes. These special modes may be modes that the hardware
can be in, or user preferences. To assign a special mode to
a particular device, append a suffix consisting of a hyphen
and an indicator of the mode to the device name. For exam-
ple, the -w suffix means "wide mode"; when specified, it
allows for a width of 132 columns instead of the standard 80
1
terminfo(4) FILE FORMATS terminfo(4)
columns. Therefore, if you want to use a vt100 device set
to wide mode, name the device "vt100-w." Use the following
suffixes where possible.
Suffix Meaning Example
-w Wide mode (more than 80 columns) 5410-w
-am With auto. margins (usually default) vt100-am
-nam Without automatic margins vt100-nam
-n Number of lines on the screen 2300-40
-na No arrow keys (leave them in local) c100-na
-np Number of pages of memory c100-4p
-rv Reverse video 4415-rv
The terminfo reference manual page is organized in two sec-
tions: "DEVICE CAPABILITIES" and "PRINTER CAPABILITIES."
PART 1: DEVICE CAPABILITIES
Capabilities in terminfo are of three types: Boolean capa-
bilities (which show that a device has or does not have a
particular feature), numeric capabilities (which quantify
particular features of a device), and string capabilities
(which provide sequences that can be used to perform partic-
ular operations on devices).
In the following table, a Variable is the name by which a C
programmer accesses a capability (at the terminfo level). A
Capname is the short name for a capability specified in the
terminfo source file. It is used by a person updating the
source file and by the tput command. A Termcap Code is a
two-letter sequence that corresponds to the termcap capabil-
ity name. (Note that termcap is no longer supported.)
Capability names have no real length limit, but an informal
limit of five characters has been adopted to keep them
short. Whenever possible, capability names are chosen to be
the same as or similar to those specified by the ANSI
X3.64-1979 standard. Semantics are also intended to match
those of the ANSI standard. All string capabilities listed
below may have padding specified, with the exception of
those used for input. Input capabilities, listed under the
Strings section in the following tables, have names begin-
ning with key. The #i symbol in the description field of
the following tables refers to the ith parameter.
Booleans
Cap- Termcap
Variable name Code Description
2
() MISC. REFERENCE MANUAL PAGES ()
auto_left_margin bw bw cub1 wraps from column 0 to
last column
auto_right_margin am am Terminal has automatic margins
back_color_erase bce be Screen erased with background color
can_change ccc cc Terminal can re-define existing color
ceol_standout_glitch xhp xs Standout not erased by overwriting (hp)
col_addr_glitch xhpa YA Only positive motion for hpa/mhpa caps
cpi_changes_res cpix YF Changing character pitch changes
resolution
cr_cancels_micro_mode crxm YB Using cr turns off micro mode
eat_newline_glitch xenl xn Newline ignored after 80 columns
(Concept)
erase_overstrike eo eo Can erase overstrikes with a blank
generic_type gn gn Generic line type (e.g., dialup, switch)
hard_copy hc hc Hardcopy terminal
hard_cursor chts HC Cursor is hard to see
has_meta_key km km Has a meta key (shift, sets parity bit)
has_print_wheel daisy YC Printer needs operator to change
character set
has_status_line hs hs Has extra "status line"
hue_lightness_saturation hls hl Terminal uses only HLS color
notation (Tektronix)
insert_null_glitch in in Insert mode distinguishes nulls
lpi_changes_res lpix YG Changing line pitch changes resolution
memory_above da da Display may be retained above the screen
memory_below db db Display may be retained below the screen
move_insert_mode mir mi Safe to move while in insert mode
move_standout_mode msgr ms Safe to move in standout modes
needs_xon_xoff nxon nx Padding won't work, xon/xoff required
no_esc_ctlc xsb xb Beehive (f1=escape, f2=ctrl C)
non_rev_rmcup nrrmc NR smcup does not reverse rmcup
no_pad_char npc NP Pad character doesn't exist
over_strike os os Terminal overstrikes on hard-copy
terminal
prtr_silent mc5i 5i Printer won't echo on screen
row_addr_glitch xvpa YD Only positive motion for vpa/mvpa caps
semi_auto_right_margin sam YE Printing in last column causes cr
status_line_esc_ok eslok es Escape can be used on the status line
dest_tabs_magic_smso xt xt Destructive tabs, magic smso char (t1061)
tilde_glitch hz hz Hazeltine; can't print tilde (~)
transparent_underline ul ul Underline character overstrikes
xon_xoff xon xo Terminal uses xon/xoff handshaking
Numbers
Cap- Termcap
Variable name Code Description
1
() MISC. REFERENCE MANUAL PAGES ()
buffer_capacity bufsz Ya Number of bytes buffered before printing
columns cols co Number of columns in a line
dot_vert_spacing spinv Yb Spacing of pins vertically in pins per inch
dot_horz_spacing spinh Yc Spacing of dots horizontally in dots per inch
init_tabs it it Tabs initially every # spaces
label_height lh lh Number of rows in each label
label_width lw lw Number of columns in each label
lines lines li Number of lines on a screen or a page
lines_of_memory lm lm Lines of memory if > lines; 0 means varies
magic_cookie_glitch xmc sg Number of blank characters left by
smso or rmso
max_colors colors Co Maximum number of colors on the screen
max_micro_address maddr Yd Maximum value in micro...address
max_micro_jump mjump Ye Maximum value in parm...micro
max_pairs pairs pa Maximum number of color-pairs on the
screen
micro_col_size mcs Yf Character step size when in micro mode
micro_line_size mls Yg Line step size when in micro mode
no_color_video ncv NC Video attributes that can't be used
with colors
number_of_pins npins Yh Number of pins in print-head
num_labels nlab Nl Number of labels on screen (start at 1)
output_res_char orc Yi Horizontal resolution in units per character
output_res_line orl Yj Vertical resolution in units per line
output_res_horz_inch orhi Yk Horizontal resolution in units per inch
output_res_vert_inch orvi Yl Vertical resolution in units per inch
padding_baud_rate pb pb Lowest baud rate where padding needed
virtual_terminal vt vt Virtual terminal number (UNIX system)
wide_char_size widcs Yn Character step size when in double
wide mode
width_status_line wsl ws Number of columns in status line
Strings
Cap- Termcap
Variable name Code Description
1
() MISC. REFERENCE MANUAL PAGES ()
acs_chars acsc ac Graphic charset pairs aAbBcC
alt_scancode_esc scesca S8 Alternate escape for scancode emulation
(default is for vt100)
back_tab cbt bt Back tab
bell bel bl Audible signal (bell)
bit_image_repeat birep Zy Repeat bit-image cell #1 #2 times (use tparm)
bit_image_newline binel Zz Move to next row of the bit image (use tparm)
bit_image_carriage_return bicr Yv Move to beginning of same row (use tparm)
carriage_return cr cr Carriage return
change_char_pitch cpi ZA Change number of characters per inch
change_line_pitch lpi ZB Change number of lines per inch
change_res_horz chr ZC Change horizontal resolution
change_res_vert cvr ZD Change vertical resolution
change_scroll_region csr cs Change to lines #1 through #2 (vt100)
char_padding rmp rP Like ip but when in replace mode
char_set_names csnm Zy List of character set names
clear_all_tabs tbc ct Clear all tab stops
clear_margins mgc MC Clear all margins (top, bottom,
and sides)
clear_screen clear cl Clear screen and home cursor
clr_bol el1 cb Clear to beginning of line, inclusive
clr_eol el ce Clear to end of line
clr_eos ed cd Clear to end of display
code_set_init csin ci Init sequence for multiple codesets
color_names colornm Yw Give name for color #1
column_address hpa ch Horizontal position absolute
command_character cmdch CC Terminal settable cmd character
in prototype
cursor_address cup cm Move to row #1 col #2
cursor_down cud1 do Down one line
cursor_home home ho Home cursor (if no cup)
cursor_invisible civis vi Make cursor invisible
cursor_left cub1 le Move left one space.
cursor_mem_address mrcup CM Memory relative cursor addressing
cursor_normal cnorm ve Make cursor appear normal
(undo vs/vi)
cursor_right cuf1 nd Non-destructive space (cursor or
carriage right)
cursor_to_ll ll ll Last line, first column (if no cup)
cursor_up cuu1 up Upline (cursor up)
cursor_visible cvvis vs Make cursor very visible
define_bit_image_region defbi Yx Define rectangular bit-image region
(use tparm)
define_char defc ZE Define a character in a character set†
delete_character dch1 dc Delete character
delete_line dl1 dl Delete line
device_type devt dv Indicate language/codeset support
dis_status_line dsl ds Disable status line
display_pc_char dispc S1 Display PC character
down_half_line hd hd Half-line down (forward 1/2 linefeed)
ena_acs enacs eA Enable alternate character set
end_bit_image_region endbi Yy End a bit-image region (use tparm)
1
() MISC. REFERENCE MANUAL PAGES ()
enter_alt_charset_mode smacs as Start alternate character set
enter_am_mode smam SA Turn on automatic margins
enter_blink_mode blink mb Turn on blinking
enter_bold_mode bold md Turn on bold (extra bright) mode
enter_ca_mode smcup ti String to begin programs that use cup
enter_delete_mode smdc dm Delete mode (enter)
enter_dim_mode dim mh Turn on half-bright mode
enter_doublewide_mode swidm ZF Enable double wide printing
enter_draft_quality sdrfq ZG Set draft quality print
enter_insert_mode smir im Insert mode (enter)
enter_italics_mode sitm ZH Enable italics
enter_leftward_mode slm ZI Enable leftward carriage motion
enter_micro_mode smicm ZJ Enable micro motion capabilities
enter_near_letter_quality snlq ZK Set near-letter quality print
enter_normal_quality snrmq ZL Set normal quality print
enter_pc_charset_mode smpch S2 Enter PC character display mode
enter_protected_mode prot mp Turn on protected mode
enter_reverse_mode rev mr Turn on reverse video mode
enter_scancode_mode smsc S4 Enter PC scancode mode
enter_secure_mode invis mk Turn on blank mode
(characters invisible)
enter_shadow_mode sshm ZM Enable shadow printing
enter_standout_mode smso so Begin standout mode
enter_subscript_mode ssubm ZN Enable subscript printing
enter_superscript_mode ssupm ZO Enable superscript printing
enter_underline_mode smul us Start underscore mode
enter_upward_mode sum ZP Enable upward carriage motion
enter_xon_mode smxon SX Turn on xon/xoff handshaking
erase_chars ech ec Erase #1 characters
exit_alt_charset_mode rmacs ae End alternate character set
exit_am_mode rmam RA Turn off automatic margins
exit_attribute_mode sgr0 me Turn off all attributes
exit_ca_mode rmcup te String to end programs that use cup
exit_delete_mode rmdc ed End delete mode
exit_doublewide_mode rwidm ZQ Disable double wide printing
exit_insert_mode rmir ei End insert mode
exit_italics_mode ritm ZR Disable italics
exit_leftward_mode rlm ZS Enable rightward (normal)
carriage motion
exit_micro_mode rmicm ZT Disable micro motion capabilities
exit_pc_charset_mode rmpch S3 Disable PC character display mode
exit_scancode_mode rmsc S5 Disable PC scancode mode
exit_shadow_mode rshm ZU Disable shadow printing
exit_standout_mode rmso se End standout mode
exit_subscript_mode rsubm ZV Disable subscript printing
exit_superscript_mode rsupm ZW Disable superscript printing
exit_underline_mode rmul ue End underscore mode
exit_upward_mode rum ZX Enable downward (normal)
carriage motion
exit_xon_mode rmxon RX Turn off xon/xoff handshaking
flash_screen flash vb Visible bell (may not move cursor)
form_feed ff ff Hardcopy terminal page eject
2
() MISC. REFERENCE MANUAL PAGES ()
from_status_line fsl fs Return from status line
init_1string is1 i1 Terminal or printer initialization string
init_2string is2 is Terminal or printer initialization string
init_3string is3 i3 Terminal or printer initialization string
init_file if if Name of initialization file
init_prog iprog iP Path name of program for initialization
initialize_color initc Ic Initialize the definition of color
initialize_pair initp Ip Initialize color-pair
insert_character ich1 ic Insert character
insert_line il1 al Add new blank line
insert_padding ip ip Insert pad after character inserted
The ``key'' strings are sent by specific keys. The
``key'' descriptions include the macro, defined in
curses.h, for the code returned by the curses routine getch
when the key is pressed [see curs_getch(3X)].
Cap- Termcap
Variable name Code Description
3
N() MISC. REFERENCE MANUAL PAGES N()
key_a1 ka1 K1 KEYA1, upper left of keypad
key_a3 ka3 K3 KEYA3, upper right of keypad
key_b2 kb2 K2 KEYB2, center of keypad
key_backspace kbs kb KEYBACKSPACE, sent by backspace key
key_beg kbeg @1 KEYBEG, sent by beg(inning) key
key_btab kcbt kB KEYBTAB, sent by back-tab key
key_c1 kc1 K4 KEYC1, lower left of keypad
key_c3 kc3 K5 KEYC3, lower right of keypad
key_cancel kcan @2 KEYCANCEL, sent by cancel key
key_catab ktbc ka KEYCATAB, sent by clear-all-tabs key
key_clear kclr kC KEYCLEAR, sent by clear-screen or
erase key
key_close kclo @3 KEYCLOSE, sent by close key
key_command kcmd @4 KEYCOMMAND, sent by cmd (command)
key
key_copy kcpy @5 KEYCOPY, sent by copy key
key_create kcrt @6 KEYCREATE, sent by create key
key_ctab kctab kt KEYCTAB, sent by clear-tab key
key_dc kdch1 kD KEYDC, sent by delete-character key
key_dl kdl1 kL KEYDL, sent by delete-line key
key_down kcud1 kd KEYDOWN, sent by terminal
down-arrow key
key_eic krmir kM KEYEIC, sent by rmir or smir in
insert mode
key_end kend @7 KEYEND, sent by end key
key_enter kent @8 KEYENTER, sent by enter/send key
key_eol kel kE KEYEOL, sent by clear-to-end-of-line
key
key_eos ked kS KEYEOS, sent by clear-to-end-of-screen
key
key_exit kext @9 KEYEXIT, sent by exit key
key_f0 kf0 k0 KEYF(0), sent by function key f0
key_f1 kf1 k1 KEYF(1), sent by function key f1
key_f2 kf2 k2 KEYF(2), sent by function key f2
key_f3 kf3 k3 KEYF(3), sent by function key f3
key_f4 kf4 k4 KEYF(4), sent by function key f4
key_f5 kf5 k5 KEYF(5), sent by function key f5
key_f6 kf6 k6 KEYF(6), sent by function key f6
key_f7 kf7 k7 KEYF(7), sent by function key f7
key_f8 kf8 k8 KEYF(8), sent by function key f8
key_f9 kf9 k9 KEYF(9), sent by function key f9
key_f10 kf10 k; KEYF(10), sent by function key f10
key_f11 kf11 F1 KEYF(11), sent by function key f11
key_f12 kf12 F2 KEYF(12), sent by function key f12
key_f13 kf13 F3 KEYF(13), sent by function key f13
key_f14 kf14 F4 KEYF(14), sent by function key f14
key_f15 kf15 F5 KEYF(15), sent by function key f15
key_f16 kf16 F6 KEYF(16), sent by function key f16
key_f17 kf17 F7 KEYF(17), sent by function key f17
key_f18 kf18 F8 KEYF(18), sent by function key f18
key_f19 kf19 F9 KEYF(19), sent by function key f19
key_f20 kf20 FA KEYF(20), sent by function key f20
1
N() MISC. REFERENCE MANUAL PAGES N()
key_f21 kf21 FB KEYF(21), sent by function key f21
key_f22 kf22 FC KEYF(22), sent by function key f22
key_f23 kf23 FD KEYF(23), sent by function key f23
key_f24 kf24 FE KEYF(24), sent by function key f24
key_f25 kf25 FF KEYF(25), sent by function key f25
key_f26 kf26 FG KEYF(26), sent by function key f26
key_f27 kf27 FH KEYF(27), sent by function key f27
key_f28 kf28 FI KEYF(28), sent by function key f28
key_f29 kf29 FJ KEYF(29), sent by function key f29
key_f30 kf30 FK KEYF(30), sent by function key f30
key_f31 kf31 FL KEYF(31), sent by function key f31
key_f32 kf32 FM KEYF(32), sent by function key f32
key_f33 kf33 FN KEYF(13), sent by function key f13
key_f34 kf34 FO KEYF(34), sent by function key f34
key_f35 kf35 FP KEYF(35), sent by function key f35
key_f36 kf36 FQ KEYF(36), sent by function key f36
key_f37 kf37 FR KEYF(37), sent by function key f37
key_f38 kf38 FS KEYF(38), sent by function key f38
key_f39 kf39 FT KEYF(39), sent by function key f39
key_f40 kf40 FU KEYF(40), sent by function key f40
key_f41 kf41 FV KEYF(41), sent by function key f41
key_f42 kf42 FW KEYF(42), sent by function key f42
key_f43 kf43 FX KEYF(43), sent by function key f43
key_f44 kf44 FY KEYF(44), sent by function key f44
key_f45 kf45 FZ KEYF(45), sent by function key f45
key_f46 kf46 Fa KEYF(46), sent by function key f46
key_f47 kf47 Fb KEYF(47), sent by function key f47
key_f48 kf48 Fc KEYF(48), sent by function key f48
key_f49 kf49 Fd KEYF(49), sent by function key f49
key_f50 kf50 Fe KEYF(50), sent by function key f50
key_f51 kf51 Ff KEYF(51), sent by function key f51
key_f52 kf52 Fg KEYF(52), sent by function key f52
key_f53 kf53 Fh KEYF(53), sent by function key f53
key_f54 kf54 Fi KEYF(54), sent by function key f54
key_f55 kf55 Fj KEYF(55), sent by function key f55
key_f56 kf56 Fk KEYF(56), sent by function key f56
key_f57 kf57 Fl KEYF(57), sent by function key f57
key_f58 kf58 Fm KEYF(58), sent by function key f58
key_f59 kf59 Fn KEYF(59), sent by function key f59
key_f60 kf60 Fo KEYF(60), sent by function key f60
key_f61 kf61 Fp KEYF(61), sent by function key f61
key_f62 kf62 Fq KEYF(62), sent by function key f62
key_f63 kf63 Fr KEYF(63), sent by function key f63
key_find kfnd @0 KEYFIND, sent by find key
key_help khlp %1 KEYHELP, sent by help key
key_home khome kh KEYHOME, sent by home key
key_ic kich1 kI KEYIC, sent by ins-char/enter
ins-mode key
key_il kil1 kA KEYIL, sent by insert-line key
key_left kcub1 kl KEYLEFT, sent by terminal left-arrow
key
key_ll kll kH KEYLL, sent by home-down key
2
N() MISC. REFERENCE MANUAL PAGES N()
key_mark kmrk %2 KEYMARK, sent by mark key
key_message kmsg %3 KEYMESSAGE, sent by message key
key_move kmov %4 KEYMOVE, sent by move key
key_next knxt %5 KEYNEXT, sent by next-object key
key_npage knp kN KEYNPAGE, sent by next-page key
key_open kopn %6 KEYOPEN, sent by open key
key_options kopt %7 KEYOPTIONS, sent by options key
key_ppage kpp kP KEYPPAGE, sent by previous-page key
key_previous kprv %8 KEYPREVIOUS, sent by previous-object
key
key_print kprt %9 KEYPRINT, sent by print or copy key
key_redo krdo %0 KEYREDO, sent by redo key
key_reference kref &1 KEYREFERENCE, sent by ref(erence) key
key_refresh krfr &2 KEYREFRESH, sent by refresh key
key_replace krpl &3 KEYREPLACE, sent by replace key
key_restart krst &4 KEYRESTART, sent by restart key
key_resume kres &5 KEYRESUME, sent by resume key
key_right kcuf1 kr KEYRIGHT, sent by terminal
right-arrow key
key_save ksav &6 KEYSAVE, sent by save key
key_sbeg kBEG &9 KEYSBEG, sent by shifted beginning key
key_scancel kCAN &0 KEYSCANCEL, sent by shifted cancel key
key_scommand kCMD *1 KEYSCOMMAND, sent by shifted
command key
key_scopy kCPY *2 KEYSCOPY, sent by shifted copy key
key_screate kCRT *3 KEYSCREATE, sent by shifted create key
key_sdc kDC *4 KEYSDC, sent by shifted delete-char key
key_sdl kDL *5 KEYSDL, sent by shifted delete-line key
key_select kslt *6 KEYSELECT, sent by select key
key_send kEND *7 KEYSEND, sent by shifted end key
key_seol kEOL *8 KEYSEOL, sent by shifted clear-line key
key_sexit kEXT *9 KEYSEXIT, sent by shifted exit key
key_sf kind kF KEYSF, sent by scroll-forward/down
key
key_sfind kFND *0 KEYSFIND, sent by shifted find key
key_shelp kHLP #1 KEYSHELP, sent by shifted help key
key_shome kHOM #2 KEYSHOME, sent by shifted home key
key_sic kIC #3 KEYSIC, sent by shifted input key
key_sleft kLFT #4 KEYSLEFT, sent by shifted left-arrow
key
key_smessage kMSG %a KEYSMESSAGE, sent by shifted message
key
key_smove kMOV %b KEYSMOVE, sent by shifted move key
key_snext kNXT %c KEYSNEXT, sent by shifted next key
key_soptions kOPT %d KEYSOPTIONS, sent by shifted options
key
key_sprevious kPRV %e KEYSPREVIOUS, sent by shifted prev
key
key_sprint kPRT %f KEYSPRINT, sent by shifted print key
key_sr kri kR KEYSR, sent by scroll-backward/up
key
key_sredo kRDO %g KEYSREDO, sent by shifted redo key
3
N() MISC. REFERENCE MANUAL PAGES N()
key_sreplace kRPL %h KEYSREPLACE, sent by shifted replace
key
key_sright kRIT %i KEYSRIGHT, sent by shifted
right-arrow key
key_srsume kRES %j KEYSRSUME, sent by shifted resume
key
key_ssave kSAV !1 KEYSSAVE, sent by shifted save key
key_ssuspend kSPD !2 KEYSSUSPEND, sent by shifted suspend
key
key_stab khts kT KEYSTAB, sent by set-tab key
key_sundo kUND !3 KEYSUNDO, sent by shifted undo key
key_suspend kspd &7 KEYSUSPEND, sent by
suspend key
key_undo kund &8 KEYUNDO, sent by undo key
key_up kcuu1 ku KEYUP, sent by terminal up-arrow key
keypad_local rmkx ke Out of ``keypad-transmit'' mode
keypad_xmit smkx ks Put terminal in ``keypad-transmit'' mode
lab_f0 lf0 l0 Labels on function key f0 if not f0
lab_f1 lf1 l1 Labels on function key f1 if not f1
lab_f2 lf2 l2 Labels on function key f2 if not f2
lab_f3 lf3 l3 Labels on function key f3 if not f3
lab_f4 lf4 l4 Labels on function key f4 if not f4
lab_f5 lf5 l5 Labels on function key f5 if not f5
lab_f6 lf6 l6 Labels on function key f6 if not f6
lab_f7 lf7 l7 Labels on function key f7 if not f7
lab_f8 lf8 l8 Labels on function key f8 if not f8
lab_f9 lf9 l9 Labels on function key f9 if not f9
lab_f10 lf10 la Labels on function key f10 if not f10
label_off rmln LF Turn off soft labels
label_on smln LO Turn on soft labels
meta_off rmm mo Turn off "meta mode"
meta_on smm mm Turn on "meta mode" (8th bit)
micro_column_address mhpa ZY Like columnaddress for micro
adjustment
micro_down mcud1 ZZ Like cursordown for micro adjustment
micro_left mcub1 Za Like cursorleft for micro adjustment
micro_right mcuf1 Zb Like cursorright for micro
adjustment
micro_row_address mvpa Zc Like rowaddress for micro adjustment
micro_up mcuu1 Zd Like cursorup for micro adjustment
newline nel nw Newline (behaves like cr followed
by lf)
order_of_pins porder Ze Matches software bits to print-head pins
orig_colors oc oc Set all color(-pair)s to the original ones
orig_pair op op Set default color-pair to the original one
pad_char pad pc Pad character (rather than null)
parm_dch dch DC Delete #1 chars
parm_delete_line dl DL Delete #1 lines
parm_down_cursor cud DO Move down #1 lines.
parm_down_micro mcud Zf Like parmdowncursor for micro
adjust.
parm_ich ich IC Insert #1 blank chars
4
N() MISC. REFERENCE MANUAL PAGES N()
parm_index indn SF Scroll forward #1 lines.
parm_insert_line il AL Add #1 new blank lines
parm_left_cursor cub LE Move cursor left #1 spaces
parm_left_micro mcub Zg Like parmleftcursor for micro
adjust.
parm_right_cursor cuf RI Move right #1 spaces.
parm_right_micro mcuf Zh Like parmrightcursor for micro
adjust.
parm_rindex rin SR Scroll backward #1 lines.
parm_up_cursor cuu UP Move cursor up #1 lines.
parm_up_micro mcuu Zi Like parmupcursor for micro adjust.
pc_term_options pctrm S6 PC terminal options
pkey_key pfkey pk Prog funct key #1 to type string #2
pkey_local pfloc pl Prog funct key #1 to execute string #2
pkey_plab pfxl xl Prog key #1 to xmit string #2 and show string #3
pkey_xmit pfx px Prog funct key #1 to xmit string #2
plab_norm pln pn Prog label #1 to show string #2
print_screen mc0 ps Print contents of the screen
prtr_non mc5p pO Turn on the printer for #1 bytes
prtr_off mc4 pf Turn off the printer
prtr_on mc5 po Turn on the printer
repeat_char rep rp Repeat char #1 #2 times
req_for_input rfi RF Send next input char (for ptys)
reset_1string rs1 r1 Reset terminal completely to sane modes
reset_2string rs2 r2 Reset terminal completely to sane modes
reset_3string rs3 r3 Reset terminal completely to sane modes
reset_file rf rf Name of file containing reset string
restore_cursor rc rc Restore cursor to position of last sc
row_address vpa cv Vertical position absolute
save_cursor sc sc Save cursor position
scancode_escape scesc S7 Escape for scancode emulation
scroll_forward ind sf Scroll text up
scroll_reverse ri sr Scroll text down
select_char_set scs Zj Select character set
set0_des_seq s0ds s0 Shift into codeset 0 (EUC set 0, ASCII)
set1_des_seq s1ds s1 Shift into codeset 1
set2_des_seq s2ds s2 Shift into codeset 2
set3_des_seq s3ds s3 Shift into codeset 3
set_a_background setab AB Set background color using ANSI escape
set_a_foreground setaf AF Set foreground color using ANSI escape
set_attributes sgr sa Define the video attributes #1-#9
set_background setb Sb Set current background color
set_bottom_margin smgb Zk Set bottom margin at current line
set_bottom_margin_parm smgbp Zl Set bottom margin at line #1 or #2
lines from bottom
set_color_band setcoloY
rz Change to ribbon color #1
set_color_pair scp sp Set current color-pair
set_foreground setf Sf Set current foreground color1
set_left_margin smgl ML Set left margin at current line
set_left_margin_parm smglp Zm Set left (right) margin at column #1 (#2)
set_lr_margin smglr ML Sets both left and right margins
set_page_length slines YZ Set page length to #1 lines (use tparm)
5
N() MISC. REFERENCE MANUAL PAGES N()
set_right_margin smgr MR Set right margin at current column
set_right_margin_parm smgrp Zn Set right margin at column #1
set_tab hts st Set a tab in all rows, current column
set_tb_margin smgtb MT Sets both top and bottom margins
set_top_margin smgt Zo Set top margin at current line
set_top_margin_parm smgtp Zp Set top (bottom) margin at line #1 (#2)
set_window wind wi Current window is lines #1-#2 cols #3-#4
start_bit_image sbim Zq Start printing bit image graphics
start_char_set_def scsd Zr Start definition of a character set
stop_bit_image rbim Zs End printing bit image graphics
stop_char_set_def rcsd Zt End definition of a character set
subscript_characters subcs Zu List of ``subscript-able'' characters
superscript_characters supcs Zv List of ``superscript-able'' characters
tab ht ta Tab to next 8-space hardware tab stop
these_cause_cr docr Zw Printing any of these chars causes cr
to_status_line tsl ts Go to status line, col #1
underline_char uc uc Underscore one char and move past it
up_half_line hu hu Half-line up (reverse 1/2 linefeed)
xoff_character xoffc XF X-off character
xon_character xonc XN X-on character
zero_motion zerom Zx No motion for the subsequent character
Sample Entry
The following entry, which describes the AT&T 610 terminal,
is among the more complex entries in the terminfo file as of
this writing.
610|610bct|ATT610|att610|AT&T610;80column;98key keyboard
am, eslok, hs, mir, msgr, xenl, xon,
cols#80, it#8, lh#2, lines#24, lw#8, nlab#8, wsl#80,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z,
civis=\E[?25l, clear=\E[H\E[J, cnorm=\E[?25h\E[?12l,
cr=\r, csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\b,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[?12;25h, dch=\E[%p1%dP, dch1=\E[P, dim=\E[2m,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K,
flash=\E[?5h$<200>\E[?5l, fsl=\E8, home=\E[H, ht=\t,
ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=\ED, .ind=\ED$<9>,
invis=\E[8m,
is1=\E[8;0 | \E[?3;4;5;13;15l\E[13;20l\E[?7h\E[12h\E(B\E)0,
is2=\E[0m^O, is3=\E(B\E)0, kLFT=\E[\s@, kRIT=\E[\sA,
kbs=^H, kcbt=\E[Z, kclr=\E[2J, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, kf1=\EOc, kf10=\ENp,
kf11=\ENq, kf12=\ENr, kf13=\ENs, kf14=\ENt, kf2=\EOd,
kf3=\EOe, kf4=\EOf, kf5=\EOg, kf6=\EOh, kf7=\EOi,
kf8=\EOj, kf9=\ENo, khome=\E[H, kind=\E[S, kri=\E[T,
ll=\E[24H, mc4=\E[?4i, mc5=\E[?5i, nel=\EE,
pfxl=\E[%p1%d;%p2%l%02dq%?%p1%{9}%<%t\s\s\sF%p1%1d\s\s\s\s\s
\s\s\s\s\s\s%;%p2%s,
pln=\E[%p1%d;0;0;0q%p2%:-16.16s, rc=\E8, rev=\E[7m,
6
N() MISC. REFERENCE MANUAL PAGES N()
ri=\EM, rmacs=^O, rmir=\E[4l, rmln=\E[2p, rmso=\E[m,
rmul=\E[m, rs2=\Ec\E[?3l, sc=\E7,
sgr=\E[0%?%p6%t;1%;%?%p5%t;2%;%?%p2%t;4%;%?%p4%t;5%;
%?%p3%p1% | %t;7%;%?%p7%t;8%;m%?%p9%t^N%e^O%;,
sgr0=\E[m^O, smacs=^N, smir=\E[4h, smln=\E[p,
smso=\E[7m, smul=\E[4m, tsl=\E7\E[25;%i%p1%dx,
Types of Capabilities in the Sample Entry
The sample entry shows the formats for the three types of
terminfo capabilities listed: Boolean, numeric, and string.
All capabilities specified in the terminfo source file must
be followed by commas, including the last capability in the
source file. In terminfo source files, capabilities are
referenced by their capability names (as shown in the previ-
ous tables). Boolean capabilities are specified simply by
their comma separated cap names.
Numeric capabilities are followed by the character `#' and
then a positive integer value. Thus, in the sample, cols
(which shows the number of columns available on a device) is
assigned the value 80 for the AT&T 610. (Values for numeric
capabilities may be specified in decimal, octal, or hexade-
cimal, using normal C programming language conventions.)
Finally, string-valued capabilities such as el (clear to end
of line sequence) are listed by a two- to five-character
capname, an `=', and a string ended by the next occurrence
of a comma. A delay in milliseconds may appear anywhere in
such a capability, preceded by $ and enclosed in angle
brackets, as in el=\EK$<3>. Padding characters are supplied
by tput. The delay can be any of the following: a number,
a number followed by an asterisk, such as 5*, a number fol-
lowed by a slash, such as 5/, or a number followed by both,
such as 5*/. A `*' shows that the padding required is pro-
portional to the number of lines affected by the operation,
and the amount given is the per-affected-unit padding
required. (In the case of insert characters, the factor is
still the number of lines affected. This is always 1 unless
the device has in and the software uses it.) When a `*' is
specified, it is sometimes useful to give a delay of the
form 3.5 to specify a delay per unit to tenths of mil-
liseconds. (Only one decimal place is allowed.)
A `/' indicates that the padding is mandatory. If a device
has xon defined, the padding information is advisory and
will only be used for cost estimates or when the device is
in raw mode. Mandatory padding will be transmitted regard-
less of the setting of xon. If padding (whether advisory or
mandatory) is specified for bel or flash, however, it will
always be used, regardless of whether xon is specified.
7
N() MISC. REFERENCE MANUAL PAGES N()
terminfo offers notation for encoding special characters.
Both \E and \e map to an ESCAPE character, ^x maps to a con-
trol x for any appropriate x, and the sequences \n, \l, \r,
\t, \b, \f, and \s give a newline, linefeed, return, tab,
backspace, formfeed, and space, respectively. Other escapes
include: \^ for caret (^); \\ for backslash (\); \, for
comma (,); \: for colon (:); and \0 for null. (\0 will
actually produce \200, which does not terminate a string but
behaves as a null character on most devices, providing CS7
is specified. [See stty(1).] Finally, characters may be
given as three octal digits after a backslash (e.g., \123).
Sometimes individual capabilities must be commented out. To
do this, put a period before the capability name. For exam-
ple, see the second ind in the example above. Note that
capabilities are defined in a left-to-right order and,
therefore, a prior definition will override a later defini-
tion.
Preparing Descriptions
The most effective way to prepare a device description is by
imitating the description of a similar device in terminfo
and building up a description gradually, using partial
descriptions with vi to check that they are correct. Be
aware that a very unusual device may expose deficiencies in
the ability of the terminfo file to describe it or the ina-
bility of vi to work with that device. To test a new device
description, set the environment variable TERMINFO to the
pathname of a directory containing the compiled description
you are working on and programs will look there rather than
in /usr/share/lib/terminfo. To get the padding for insert-
line correct (if the device manufacturer did not document
it) a severe test is to comment out xon, edit a large file
at 9600 baud with vi, delete 16 or so lines from the middle
of the screen, and then press the u key several times
quickly. If the display is corrupted, more padding is usu-
ally needed. A similar test can be used for insert-
character.
Section 1-1: Basic Capabilities
The number of columns on each line for the device is given
by the cols numeric capability. If the device has a screen,
then the number of lines on the screen is given by the lines
capability. If the device wraps around to the beginning of
the next line when it reaches the right margin, then it
should have the am capability. If the terminal can clear
its screen, leaving the cursor in the home position, then
this is given by the clear string capability. If the termi-
nal overstrikes (rather than clearing a position when a
character is struck over) then it should have the os capa-
bility. If the device is a printing terminal, with no soft
copy unit, specify both hc and os. If there is a way to
8
N() MISC. REFERENCE MANUAL PAGES N()
move the cursor to the left edge of the current row, specify
this as cr. (Normally this will be carriage return, control
M.) If there is a way to produce an audible signal (such as
a bell or a beep), specify it as bel. If, like most dev-
ices, the device uses the xon-xoff flow-control protocol,
specify xon.
If there is a way to move the cursor one position to the
left (such as backspace), that capability should be given as
cub1. Similarly, sequences to move to the right, up, and
down should be given as cuf1, cuu1, and cud1, respectively.
These local cursor motions must not alter the text they pass
over; for example, you would not normally use ``cuf1=\s''
because the space would erase the character moved over.
A very important point here is that the local cursor motions
encoded in terminfo are undefined at the left and top edges
of a screen terminal. Programs should never attempt to
backspace around the left edge, unless bw is specified, and
should never attempt to go up locally off the top. To
scroll text up, a program goes to the bottom left corner of
the screen and sends the ind (index) string.
To scroll text down, a program goes to the top left corner
of the screen and sends the ri (reverse index) string. The
strings ind and ri are undefined when not on their respec-
tive corners of the screen.
Parameterized versions of the scrolling sequences are indn
and rin. These versions have the same semantics as ind and
ri, except that they take one parameter and scroll the
number of lines specified by that parameter. They are also
undefined except at the appropriate edge of the screen.
The am capability tells whether the cursor sticks at the
right edge of the screen when text is output, but this does
not necessarily apply to a cuf1 from the last column. Back-
ward motion from the left edge of the screen is possible
only when bw is specified. In this case, cub1 will move to
the right edge of the previous row. If bw is not given, the
effect is undefined. This is useful for drawing a box
around the edge of the screen, for example. If the device
has switch selectable automatic margins, am should be speci-
fied in the terminfo source file. In this case, initializa-
tion strings should turn on this option, if possible. If
the device has a command that moves to the first column of
the next line, that command can be given as nel (newline).
It does not matter if the command clears the remainder of
the current line, so if the device has no cr and lf it may
still be possible to craft a working nel out of one or both
of them.
9
N() MISC. REFERENCE MANUAL PAGES N()
These capabilities suffice to describe hardcopy and screen
terminals. Thus the AT&T 5320 hardcopy terminal is
described as follows:
5320|att5320|AT&T 5320 hardcopy terminal,
am, hc, os,
cols#132,
bel=^G, cr=\r, cub1=\b, cnd1=\n,
dch1=\E[P, dl1=\E[M,
ind=\n,
while the Lear Siegler ADM-3 is described as
adm3|lsi adm3,
am, bel=^G, clear=^Z, cols#80, cr=^M, cub1=^H,
cud1=^J, ind=^J, lines#24,
Section 1-2: Parameterized Strings
Cursor addressing and other strings requiring parameters are
described by a parameterized string capability, with
printf-like escapes (%x) in it. For example, to address the
cursor, the cup capability is given, using two parameters:
the row and column to address to. (Rows and columns are
numbered from zero and refer to the physical screen visible
to the user, not to any unseen memory.) If the terminal has
memory relative cursor addressing, that can be indicated by
mrcup.
The parameter mechanism uses a stack and special % codes to
manipulate the stack in the manner of Reverse Polish Nota-
tion (postfix). Typically a sequence will push one of the
parameters onto the stack and then print it in some format.
Often more complex operations are necessary. Operations are
in postfix form with the operands in the usual order. That
is, to subtract 5 from the first parameter, one would use
%p1%{5}%-.
The % encodings have the following meanings:
%% outputs `%'
%[[:]flags][width[.precision]][doxXs]
as in printf, flags are [-+#] and space
%c print pop gives %c
%p[1-9]
push ith parm
%P[a-z]
set dynamic variable [a-z] to pop
10
N() MISC. REFERENCE MANUAL PAGES N()
%g[a-z]
get dynamic variable [a-z] and push it
%P[A-Z]
set static variable [a-z] to pop
%g[A-Z]
get static variable [a-z] and push it
%'c' push char constant c
%{nn}
push decimal constant nn
%l push strlen(pop)
%+ %- %* %/ %m
arithmetic (%m is mod): push(pop integer2 op pop
integer1)
%& %| %^
bit operations: push(pop integer2 op pop integer1)
%= %> %<
logical operations: push(pop integer2 op pop integer1)
%A %O
logical operations: and, or
%! %~
unary operations: push(op pop)
%i (for ANSI terminals) add 1 to first parm, if one parm
present, or first two parms, if more than one parm
present
%? expr %t thenpart %e elsepart %;
if-then-else, %e elsepart is optional; else-if's are
possible ala Algol 68: %? c1 %t b1 %e c2 %t b2 %e c3
%t b3 %e c4 %t b4 %e b5%;
ci are conditions, bi are bodies.
If the ``-'' flag is used with ``%[doxXs]'', then a colon
(:) must be placed between the ``%'' and the ``-'' to dif-
ferentiate the flag from the binary ``%-'' operator, e.g.
``%:-16.16s''.
Consider the Hewlett-Packard 2645, which, to get to row 3
and column 12, needs to be sent \E&a12c03Y padded for 6 mil-
liseconds. Note that the order of the rows and columns is
inverted here, and that the row and column are zero-padded
as two digits. Thus its cup capability is:
11
N() MISC. REFERENCE MANUAL PAGES N()
cup=\E&a%p2%2.2dc%p1%2.2dY$<6>
The Micro-Term ACT-IV needs the current row and column sent
preceded by a ^T, with the row and column simply encoded in
binary, ``cup=^T%p1%c%p2%c''. Devices that use ``%c'' need
to be able to backspace the cursor (cub1), and to move the
cursor up one line on the screen (cuu1). This is necessary
because it is not always safe to transmit \n, ^D, and \r, as
the system may change or discard them. (The library rou-
tines dealing with terminfo set tty modes so that tabs are
never expanded, so \t is safe to send. This turns out to be
essential for the Ann Arbor 4080.)
A final example is the LSI ADM-3a, which uses row and column
offset by a blank character, thus
``cup=\E=%p1%'\s'%+%c%p2%'\s'%+%c''. After sending ``\E='',
this pushes the first parameter, pushes the ASCII value for
a space (32), adds them (pushing the sum on the stack in
place of the two previous values), and outputs that value as
a character. Then the same is done for the second parame-
ter. More complex arithmetic is possible using the stack.
Section 1-3: Cursor Motions
If the terminal has a fast way to home the cursor (to very
upper left corner of screen) then this can be given as home;
similarly a fast way of getting to the lower left-hand
corner can be given as ll; this may involve going up with
cuu1 from the home position, but a program should never do
this itself (unless ll does) because it can make no assump-
tion about the effect of moving up from the home position.
Note that the home position is the same as addressing to
(0,0): to the top left corner of the screen, not of memory.
(Thus, the \EH sequence on Hewlett-Packard terminals cannot
be used for home without losing some of the other features
on the terminal.)
If the device has row or column absolute-cursor addressing,
these can be given as single parameter capabilities hpa
(horizontal position absolute) and vpa (vertical position
absolute). Sometimes these are shorter than the more gen-
eral two-parameter sequence (as with the Hewlett-Packard
2645) and can be used in preference to cup. If there are
parameterized local motions (e.g., move n spaces to the
right) these can be given as cud, cub, cuf, and cuu with a
single parameter indicating how many spaces to move. These
are primarily useful if the device does not have cup, such
as the Tektronix 4025.
If the device needs to be in a special mode when running a
program that uses these capabilities, the codes to enter and
exit this mode can be given as smcup and rmcup. This
arises, for example, from terminals, such as the Concept,
12
N() MISC. REFERENCE MANUAL PAGES N()
with more than one page of memory. If the device has only
memory relative cursor addressing and not screen relative
cursor addressing, a one screen-sized window must be fixed
into the device for cursor addressing to work properly.
This is also used for the Tektronix 4025, where smcup sets
the command character to be the one used by terminfo. If
the smcup sequence will not restore the screen after an
rmcup sequence is output (to the state prior to outputting
rmcup), specify nrrmc.
Section 1-4: Area Clears
If the terminal can clear from the current position to the
end of the line, leaving the cursor where it is, this should
be given as el. If the terminal can clear from the begin-
ning of the line to the current position inclusive, leaving
the cursor where it is, this should be given as el1. If the
terminal can clear from the current position to the end of
the display, then this should be given as ed. ed is only
defined from the first column of a line. (Thus, it can be
simulated by a request to delete a large number of lines, if
a true ed is not available.)
Section 1-5: Insert/Delete Line
If the terminal can open a new blank line before the line
where the cursor is, this should be given as il1; this is
done only from the first position of a line. The cursor
must then appear on the newly blank line. If the terminal
can delete the line which the cursor is on, then this should
be given as dl1; this is done only from the first position
on the line to be deleted. Versions of il1 and dl1 which
take a single parameter and insert or delete that many lines
can be given as il and dl. If the terminal has a settable
destructive scrolling region (like the VT100) the command to
set this can be described with the csr capability, which
takes two parameters: the top and bottom lines of the
scrolling region. The cursor position is, alas, undefined
after using this command. It is possible to get the effect
of insert or delete line using this command - the sc and rc
(save and restore cursor) commands are also useful. Insert-
ing lines at the top or bottom of the screen can also be
done using ri or ind on many terminals without a true
insert/delete line, and is often faster even on terminals
with those features. To determine whether a terminal has
destructive scrolling regions or non-destructive scrolling
regions, create a scrolling region in the middle of the
screen, place data on the bottom line of the scrolling
region, move the cursor to the top line of the scrolling
region, and do a reverse index (ri) followed by a delete
line (dl1) or index (ind). If the data that was originally
on the bottom line of the scrolling region was restored into
the scrolling region by the dl1 or ind, then the terminal
has non-destructive scrolling regions. Otherwise, it has
13
N() MISC. REFERENCE MANUAL PAGES N()
destructive scrolling regions. Do not specify csr if the
terminal has non-destructive scrolling regions, unless ind,
ri, indn, rin, dl, and dl1 all simulate destructive scrol-
ling.
If the terminal has the ability to define a window as part
of memory, which all commands affect, it should be given as
the parameterized string wind. The four parameters are the
starting and ending lines in memory and the starting and
ending columns in memory, in that order.
If the terminal can retain display memory above, then the da
capability should be given; if display memory can be
retained below, then db should be given. These indicate
that deleting a line or scrolling a full screen may bring
non-blank lines up from below or that scrolling back with ri
may bring down non-blank lines.
Section 1-6: Insert/Delete Character
There are two basic kinds of intelligent terminals with
respect to insert/delete character operations which can be
described using terminfo. The most common insert/delete
character operations affect only the characters on the
current line and shift characters off the end of the line
rigidly. Other terminals, such as the Concept 100 and the
Perkin Elmer Owl, make a distinction between typed and
untyped blanks on the screen, shifting upon an insert or
delete only to an untyped blank on the screen which is
either eliminated, or expanded to two untyped blanks. You
can determine the kind of terminal you have by clearing the
screen and then typing text separated by cursor motions.
Type ``abc def'' using local cursor motions (not spaces)
between the abc and the def. Then position the cursor
before the abc and put the terminal in insert mode. If typ-
ing characters causes the rest of the line to shift rigidly
and characters to fall off the end, then your terminal does
not distinguish between blanks and untyped positions. If
the abc shifts over to the def which then move together
around the end of the current line and onto the next as you
insert, you have the second type of terminal, and should
give the capability in, which stands for ``insert null.''
While these are two logically separate attributes (one line
versus multiline insert mode, and special treatment of
untyped spaces) we have seen no terminals whose insert mode
cannot be described with the single attribute.
terminfo can describe both terminals that have an insert
mode and terminals which send a simple sequence to open a
blank position on the current line. Give as smir the
sequence to get into insert mode. Give as rmir the sequence
to leave insert mode. Now give as ich1 any sequence needed
to be sent just before sending the character to be inserted.
14
N() MISC. REFERENCE MANUAL PAGES N()
Most terminals with a true insert mode will not give ich1;
terminals that send a sequence to open a screen position
should give it here. (If your terminal has both, insert
mode is usually preferable to ich1. Do not give both unless
the terminal actually requires both to be used in combina-
tion.) If post-insert padding is needed, give this as a
number of milliseconds padding in ip (a string option). Any
other sequence which may need to be sent after an insert of
a single character may also be given in ip. If your termi-
nal needs both to be placed into an `insert mode' and a spe-
cial code to precede each inserted character, then both
smir/rmir and ich1 can be given, and both will be used. The
ich capability, with one parameter, n, will insert n blanks.
If padding is necessary between characters typed while not
in insert mode, give this as a number of milliseconds pad-
ding in rmp.
It is occasionally necessary to move around while in insert
mode to delete characters on the same line (e.g., if there
is a tab after the insertion position). If your terminal
allows motion while in insert mode you can give the capabil-
ity mir to speed up inserting in this case. Omitting mir
will affect only speed. Some terminals (notably
Datamedia's) must not have mir because of the way their
insert mode works.
Finally, you can specify dch1 to delete a single character,
dch with one parameter, n, to delete n characters, and
delete mode by giving smdc and rmdc to enter and exit delete
mode (any mode the terminal needs to be placed in for dch1
to work).
A command to erase n characters (equivalent to outputting n
blanks without moving the cursor) can be given as ech with
one parameter.
Section 1-7: Highlighting, Underlining, and Visible Bells
Your device may have one or more kinds of display attributes
that allow you to highlight selected characters when they
appear on the screen. The following display modes (shown
with the names by which they are set) may be available: a
blinking screen (blink), bold or extra-bright characters
(bold), dim or half-bright characters (dim), blanking or
invisible text (invis), protected text (prot), a reverse-
video screen (rev), and an alternate character set (smacs to
enter this mode and rmacs to exit it). (If a command is
necessary before you can enter alternate character set mode,
give the sequence in enacs or "enable alternate-character-
set" mode.) Turning on any of these modes singly may or may
not turn off other modes.
15
N() MISC. REFERENCE MANUAL PAGES N()
sgr0 should be used to turn off all video enhancement capa-
bilities. It should always be specified because it
represents the only way to turn off some capabilities, such
as dim or blink.
You should choose one display method as standout mode [see
curses(3X)] and use it to highlight error messages and other
kinds of text to which you want to draw attention. Choose a
form of display that provides strong contrast but that is
easy on the eyes. (We recommend reverse-video plus half-
bright or reverse-video alone.) The sequences to enter and
exit standout mode are given as smso and rmso, respectively.
If the code to change into or out of standout mode leaves
one or even two blank spaces on the screen, as the TVI 912
and Teleray 1061 do, then xmc should be given to tell how
many spaces are left.
Sequences to begin underlining and end underlining can be
specified as smul and rmul , respectively. If the device
has a sequence to underline the current character and to
move the cursor one space to the right (such as the Micro-
Term MIME), this sequence can be specified as uc.
Terminals with the ``magic cookie'' glitch (xmc) deposit
special ``cookies'' when they receive mode-setting
sequences, which affect the display algorithm rather than
having extra bits for each character. Some terminals, such
as the Hewlett-Packard 2621, automatically leave standout
mode when they move to a new line or the cursor is
addressed. Programs using standout mode should exit stan-
dout mode before moving the cursor or sending a newline,
unless the msgr capability, asserting that it is safe to
move in standout mode, is present.
If the terminal has a way of flashing the screen to indicate
an error quietly (a bell replacement), then this can be
given as flash; it must not move the cursor. A good flash
can be done by changing the screen into reverse video, pad
for 200 ms, then return the screen to normal video.
If the cursor needs to be made more visible than normal when
it is not on the bottom line (to make, for example, a non-
blinking underline into an easier to find block or blinking
underline) give this sequence as cvvis. The boolean chts
should also be given. If there is a way to make the cursor
completely invisible, give that as civis. The capability
cnorm should be given which undoes the effects of either of
these modes.
If your terminal generates underlined characters by using
the underline character (with no special sequences needed)
even though it does not otherwise overstrike characters,
16
N() MISC. REFERENCE MANUAL PAGES N()
then you should specify the capability ul. For devices on
which a character overstriking another leaves both charac-
ters on the screen, specify the capability os. If over-
strikes are erasable with a blank, then this should be indi-
cated by specifying eo.
If there is a sequence to set arbitrary combinations of
modes, this should be given as sgr (set attributes), taking
nine parameters. Each parameter is either 0 or non-zero, as
the corresponding attribute is on or off. The nine parame-
ters are, in order: standout, underline, reverse, blink,
dim, bold, blank, protect, alternate character set. Not all
modes need to be supported by sgr; only those for which
corresponding separate attribute commands exist should be
supported. For example, let's assume that the terminal in
question needs the following escape sequences to turn on
various modes.
tparm
parameter attribute escape sequence
none \E[0m
p1 standout \E[0;4;7m
p2 underline \E[0;3m
p3 reverse \E[0;4m
p4 blink \E[0;5m
p5 dim \E[0;7m
p6 bold \E[0;3;4m
p7 invis \E[0;8m
p8 protect not available
p9 altcharset ^O (off) ^N (on)
Note that each escape sequence requires a 0 to turn off
other modes before turning on its own mode. Also note that,
as suggested above, standout is set up to be the combination
of reverse and dim. Also, because this terminal has no bold
mode, bold is set up as the combination of reverse and
underline. In addition, to allow combinations, such as
underline+blink, the sequence to use would be \E[0;3;5m.
The terminal doesn't have protect mode, either, but that
cannot be simulated in any way, so p8 is ignored. The
altcharset mode is different in that it is either ^O or ^N,
depending on whether it is off or on. If all modes were to
be turned on, the sequence would be \E[0;3;4;5;7;8m^N.
Now look at when different sequences are output. For exam-
ple, ;3 is output when either p2 or p6 is true, that is, if
either underline or bold modes are turned on. Writing out
the above sequences, along with their dependencies, gives
the following:
sequence when to output terminfo translation
\E[0 always \E[0
;3 if p2 or p6 %?%p2%p6%|%t;3%;
;4 if p1 or p3 or p6 %?%p1%p3%|%p6%|%t;4%;
17
N() MISC. REFERENCE MANUAL PAGES N()
;5 if p4 %?%p4%t;5%;
;7 if p1 or p5 %?%p1%p5%|%t;7%;
;8 if p7 %?%p7%t;8%;
m always m
^N or ^O if p9 ^N, else ^O %?%p9%t^N%e^O%;
Putting this all together into the sgr sequence gives:
sgr=\E[0%?%p2%p6%|%t;3%;%?%p1%p3%|%p6%
|%t;4%;%?%p5%t;5%;%?%p1%p5%
|%t;7%;%?%p7%t;8%;m%?%p9%t^N%e^O%;,
Remember that sgr and sgr0 must always be specified.
Section 1-8: Keypad
If the device has a keypad that transmits sequences when the
keys are pressed, this information can also be specified.
Note that it is not possible to handle devices where the
keypad only works in local (this applies, for example, to
the unshifted Hewlett-Packard 2621 keys). If the keypad can
be set to transmit or not transmit, specify these sequences
as smkx and rmkx. Otherwise the keypad is assumed to always
transmit.
The sequences sent by the left arrow, right arrow, up arrow,
down arrow, and home keys can be given as kcub1, kcuf1,
kcuu1, kcud1, and khome, respectively. If there are func-
tion keys such as f0, f1, ..., f63, the sequences they send
can be specified as kf0, kf1, ..., kf63. If the first 11
keys have labels other than the default f0 through f10, the
labels can be given as lf0, lf1, ..., lf10. The codes
transmitted by certain other special keys can be given: kll
(home down), kbs (backspace), ktbc (clear all tabs), kctab
(clear the tab stop in this column), kclr (clear screen or
erase key), kdch1 (delete character), kdl1 (delete line),
krmir (exit insert mode), kel (clear to end of line), ked
(clear to end of screen), kich1 (insert character or enter
insert mode), kil1 (insert line), knp (next page), kpp (pre-
vious page), kind (scroll forward/down), kri (scroll
backward/up), khts (set a tab stop in this column). In
addition, if the keypad has a 3 by 3 array of keys including
the four arrow keys, the other five keys can be given as
ka1, ka3, kb2, kc1, and kc3. These keys are useful when the
effects of a 3 by 3 directional pad are needed. Further
keys are defined above in the capabilities list.
Strings to program function keys can be specified as pfkey,
pfloc, and pfx. A string to program screen labels should be
specified as pln. Each of these strings takes two parame-
ters: a function key identifier and a string to program it
with. pfkey causes pressing the given key to be the same as
the user typing the given string; pfloc causes the string to
18
N() MISC. REFERENCE MANUAL PAGES N()
be executed by the terminal in local mode; and pfx causes
the string to be transmitted to the computer. The capabili-
ties nlab, lw and lh define the number of programmable
screen labels and their width and height. If there are com-
mands to turn the labels on and off, give them in smln and
rmln. smln is normally output after one or more pln
sequences to make sure that the change becomes visible.
Section 1-9: Tabs and Initialization
If the device has hardware tabs, the command to advance to
the next tab stop can be given as ht (usually control I). A
``backtab'' command that moves leftward to the next tab stop
can be given as cbt. By convention, if tty modes show that
tabs are being expanded by the computer rather than being
sent to the device, programs should not use ht or cbt (even
if they are present) because the user may not have the tab
stops properly set. If the device has hardware tabs that
are initially set every n spaces when the device is powered
up, the numeric parameter it is given, showing the number of
spaces the tabs are set to. This is normally used by tput
init [see tput(1)] to determine whether to set the mode for
hardware tab expansion and whether to set the tab stops. If
the device has tab stops that can be saved in nonvolatile
memory, the terminfo description can assume that they are
properly set. If there are commands to set and clear tab
stops, they can be given as tbc (clear all tab stops) and
hts (set a tab stop in the current column of every row).
Other capabilities include: is1, is2, and is3, initializa-
tion strings for the device; iprog, the path name of a pro-
gram to be run to initialize the device; and if, the name of
a file containing long initialization strings. These
strings are expected to set the device into modes consistent
with the rest of the terminfo description. They must be
sent to the device each time the user logs in and be output
in the following order: run the program iprog; output is1;
output is2; set the margins using mgc, smgl and smgr; set
the tabs using tbc and hts; print the file if; and finally
output is3. This is usually done using the init option of
tput. Most initialization is done with is2. Special device
modes can be set up without duplicating strings by putting
the common sequences in is2 and special cases in is1 and
is3. Sequences that do a reset from a totally unknown state
can be given as rs1, rs2, rf, and rs3, analogous to is1,
is2, is3, and if. (The method using files, if and rf, is
used for a few terminals, from /usr/share/lib/tabset/*; how-
ever, the recommended method is to use the initialization
and reset strings.) These strings are output by tput reset,
which is used when the terminal gets into a wedged state.
Commands are normally placed in rs1, rs2, rs3, and rf only
if they produce annoying effects on the screen and are not
necessary when logging in. For example, the command to set
19
N() MISC. REFERENCE MANUAL PAGES N()
a terminal into 80-column mode would normally be part of
is2, but on some terminals it causes an annoying glitch on
the screen and is not normally needed because the terminal
is usually already in 80-column mode.
If a more complex sequence is needed to set the tabs than
can be described by using tbc and hts, the sequence can be
placed in is2 or if.
Any margin can be cleared with mgc. (For instructions on
how to specify commands to set and clear margins, see "Mar-
gins" below under "PRINTER CAPABILITIES.")
Section 1-10: Delays
Certain capabilities control padding in the tty driver.
These are primarily needed by hard-copy terminals, and are
used by tput init to set tty modes appropriately. Delays
embedded in the capabilities cr, ind, cub1, ff, and tab can
be used to set the appropriate delay bits to be set in the
tty driver. If pb (padding baud rate) is given, these
values can be ignored at baud rates below the value of pb.
Section 1-11: Status Lines
If the terminal has an extra ``status line'' that is not
normally used by software, this fact can be indicated. If
the status line is viewed as an extra line below the bottom
line, into which one can cursor address normally (such as
the Heathkit h19's 25th line, or the 24th line of a VT100
which is set to a 23-line scrolling region), the capability
hs should be given. Special strings that go to a given
column of the status line and return from the status line
can be given as tsl and fsl. (fsl must leave the cursor
position in the same place it was before tsl. If necessary,
the sc and rc strings can be included in tsl and fsl to get
this effect.) The capability tsl takes one parameter, which
is the column number of the status line the cursor is to be
moved to.
If escape sequences and other special commands, such as tab,
work while in the status line, the flag eslok can be given.
A string which turns off the status line (or otherwise
erases its contents) should be given as dsl. If the termi-
nal has commands to save and restore the position of the
cursor, give them as sc and rc. The status line is normally
assumed to be the same width as the rest of the screen,
e.g., cols. If the status line is a different width (possi-
bly because the terminal does not allow an entire line to be
loaded) the width, in columns, can be indicated with the
numeric parameter wsl.
Section 1-12: Line Graphics
If the device has a line drawing alternate character set,
20
N() MISC. REFERENCE MANUAL PAGES N()
the mapping of glyph to character would be given in acsc.
The definition of this string is based on the alternate
character set used in the DEC VT100 terminal, extended
slightly with some characters from the AT&T 4410v1 terminal.
vt100+
glyph name character
arrow pointing right +
arrow pointing left ,
arrow pointing down .
solid square block 0
lantern symbol I
arrow pointing up -
diamond `
checker board (stipple) a
degree symbol f
plus/minus g
board of squares h
lower right corner j
upper right corner k
upper left corner l
lower left corner m
plus n
scan line 1 o
horizontal line q
scan line 9 s
left tee (†) t
right tee (-|) u
bottom tee (|) v
|) top t
wee (
vertical line x
bullet ~
The best way to describe a new device's line graphics set is
to add a third column to the above table with the characters
for the new device that produce the appropriate glyph when
the device is in the alternate character set mode. For
example,
vt100+ new tty
glyph name char char
upper left corner l R
lower left corner m F
upper right corner k T
lower right corner j G
horizontal line q ,
vertical line x .
Now write down the characters left to right, as in
``acsc=lRmFkTjGq\,x.''.
21
N() MISC. REFERENCE MANUAL PAGES N()
In addition, terminfo allows you to define multiple charac-
ter sets. See Section 2-5 for details.
Section 1-13: Color Manipulation
Let us define two methods of color manipulation: the Tek-
tronix method and the HP method. The Tektronix method uses
a set of N predefined colors (usually 8) from which a user
can select "current" foreground and background colors. Thus
a terminal can support up to N colors mixed into N*N color-
pairs to be displayed on the screen at the same time. When
using an HP method the user cannot define the foreground
independently of the background, or vice-versa. Instead,
the user must define an entire color-pair at once. Up to M
color-pairs, made from 2*M different colors, can be defined
this way. Most existing color terminals belong to one of
these two classes of terminals.
The numeric variables colors and pairs define the number of
colors and color-pairs that can be displayed on the screen
at the same time. If a terminal can change the definition
of a color (for example, the Tektronix 4100 and 4200 series
terminals), this should be specified with ccc (can change
color). To change the definition of a color (Tektronix 4200
method), use initc (initialize color). It requires four
arguments: color number (ranging from 0 to colors-1) and
three RGB (red, green, and blue) values or three HLS colors
(Hue, Lightness, Saturation). Ranges of RGB and HLS values
are terminal dependent.
Tektronix 4100 series terminals only use HLS color notation.
For such terminals (or dual-mode terminals to be operated in
HLS mode) one must define a boolean variable hls; that would
instruct the curses initcolor routine to convert its RGB
arguments to HLS before sending them to the terminal. The
last three arguments to the initc string would then be HLS
values.
If a terminal can change the definitions of colors, but uses
a color notation different from RGB and HLS, a mapping to
either RGB or HLS must be developed.
To set current foreground or background to a given color,
use setaf (set ANSI foreground) and setab (set ANSI back-
ground). They require one parameter: the number of the
color. To initialize a color-pair (HP method), use initp
(initialize pair). It requires seven parameters: the
number of a color-pair (range=0 to pairs-1), and six RGB
values: three for the foreground followed by three for the
background. (Each of these groups of three should be in the
order RGB.) When initc or initp are used, RGB or HLS argu-
ments should be in the order "red, green, blue" or "hue,
lightness, saturation"), respectively. To make a color-pair
22
N() MISC. REFERENCE MANUAL PAGES N()
current, use scp (set color-pair). It takes one parameter,
the number of a color-pair.
Some terminals (for example, most color terminal emulators
for PCs) erase areas of the screen with current background
color. In such cases, bce (background color erase) should
be defined. The variable op (original pair) contains a
sequence for setting the foreground and the background
colors to what they were at the terminal start-up time.
Similarly, oc (original colors) contains a control sequence
for setting all colors (for the Tektronix method) or color-
pairs (for the HP method) to the values they had at the ter-
minal start-up time.
Some color terminals substitute color for video attributes.
Such video attributes should not be combined with colors.
Information about these video attributes should be packed
into the ncv (no color video) variable. There is a one-to-
one correspondence between the nine least significant bits
of that variable and the video attributes. The following
table depicts this correspondence.
Bit Decimal
Attribute Position Value
_________________________________
A_STANDOUT 0 1
A_UNDERLINE 1 2
A_REVERSE 2 4
A_BLINK 3 8
A_DIM 4 16
A_BOLD 5 32
A_INVIS 6 64
A_PROTECT 7 128
A_ALTCHARSET 8 256
When a particular video attribute should not be used with
colors, the corresponding ncv bit should be set to 1; other-
wise it should be set to zero. To determine the information
to pack into the ncv variable, you must add together the
decimal values corresponding to those attributes that cannot
coexist with colors. For example, if the terminal uses
colors to simulate reverse video (bit number 2 and decimal
value 4) and bold (bit number 5 and decimal value 32), the
resulting value for ncv will be 36 (4 + 32).
Section 1-14: Miscellaneous
If the terminal requires other than a null (zero) character
as a pad, then this can be given as pad. Only the first
character of the pad string is used. If the terminal does
not have a pad character, specify npc.
23
N() MISC. REFERENCE MANUAL PAGES N()
If the terminal can move up or down half a line, this can be
indicated with hu (half-line up) and hd (half-line down).
This is primarily useful for superscripts and subscripts on
hardcopy terminals. If a hardcopy terminal can eject to the
next page (form feed), give this as ff (usually control L).
If there is a command to repeat a given character a given
number of times (to save time transmitting a large number of
identical characters) this can be indicated with the
parameterized string rep. The first parameter is the char-
acter to be repeated and the second is the number of times
to repeat it. Thus, tparm(repeatchar, 'x', 10) is the same
as xxxxxxxxxx.
If the terminal has a settable command character, such as
the Tektronix 4025, this can be indicated with cmdch. A
prototype command character is chosen which is used in all
capabilities. This character is given in the cmdch capabil-
ity to identify it. The following convention is supported
on some UNIX systems: If the environment variable CC
exists, all occurrences of the prototype character are
replaced with the character in CC.
Terminal descriptions that do not represent a specific kind
of known terminal, such as switch, dialup, patch, and net-
work, should include the gn (generic) capability so that
programs can complain that they do not know how to talk to
the terminal. (This capability does not apply to virtual
terminal descriptions for which the escape sequences are
known.) If the terminal is one of those supported by the
UNIX system virtual terminal protocol, the terminal number
can be given as vt. A line-turn-around sequence to be
transmitted before doing reads should be specified in rfi.
If the device uses xon/xoff handshaking for flow control,
give xon. Padding information should still be included so
that routines can make better decisions about costs, but
actual pad characters will not be transmitted. Sequences to
turn on and off xon/xoff handshaking may be given in smxon
and rmxon. If the characters used for handshaking are not
^S and ^Q, they may be specified with xonc and xoffc.
If the terminal has a ``meta key'' which acts as a shift
key, setting the 8th bit of any character transmitted, this
fact can be indicated with km. Otherwise, software will
assume that the 8th bit is parity and it will usually be
cleared. If strings exist to turn this ``meta mode'' on and
off, they can be given as smm and rmm.
If the terminal has more lines of memory than will fit on
the screen at once, the number of lines of memory can be
indicated with lm. A value of lm#0 indicates that the
24
N() MISC. REFERENCE MANUAL PAGES N()
number of lines is not fixed, but that there is still more
memory than fits on the screen.
Media copy strings which control an auxiliary printer con-
nected to the terminal can be given as mc0: print the con-
tents of the screen, mc4: turn off the printer, and mc5:
turn on the printer. When the printer is on, all text sent
to the terminal will be sent to the printer. A variation,
mc5p, takes one parameter, and leaves the printer on for as
many characters as the value of the parameter, then turns
the printer off. The parameter should not exceed 255. If
the text is not displayed on the terminal screen when the
printer is on, specify mc5i (silent printer). All text,
including mc4, is transparently passed to the printer while
an mc5p is in effect.
Section 1-15: Special Cases
The working model used by terminfo fits most terminals rea-
sonably well. However, some terminals do not completely
match that model, requiring special support by terminfo.
These are not meant to be construed as deficiencies in the
terminals; they are just differences between the working
model and the actual hardware. They may be unusual devices
or, for some reason, do not have all the features of the
terminfo model implemented. Terminals that cannot display
tilde (~) characters, such as certain Hazeltine terminals,
should indicate hz. Terminals that ignore a linefeed
immediately after an am wrap, such as the Concept 100,
should indicate xenl. Those terminals whose cursor remains
on the right-most column until another character has been
received, rather than wrapping immediately upon receiving
the right-most character, such as the VT100, should also
indicate xenl. If el is required to get rid of standout
(instead of writing normal text on top of it), xhp should be
given. Those Teleray terminals whose tabs turn all charac-
ters moved over to blanks, should indicate xt (destructive
tabs). This capability is also taken to mean that it is not
possible to position the cursor on top of a ``magic
cookie.'' Therefore, to erase standout mode, it is neces-
sary, instead, to use delete and insert line. Those Beehive
Superbee terminals which do not transmit the escape or
control-C characters, should specify xsb, indicating that
the f1 key is to be used for escape and the f2 key for con-
trol C.
Section 1-16: Similar Terminals
If there are two very similar terminals, one can be defined
as being just like the other with certain exceptions. The
string capability use can be given with the name of the
similar terminal. The capabilities given before use over-
ride those in the terminal type invoked by use. A capabil-
ity can be canceled by placing xx@ to the left of the
25
N() MISC. REFERENCE MANUAL PAGES N()
capability definition, where xx is the capability. For
example, the entry
att4424-2|Teletype 4424 in display function group ii,
rev@, sgr@, smul@, use=att4424,
defines an AT&T 4424 terminal that does not have the rev,
sgr, and smul capabilities, and hence cannot do highlight-
ing. This is useful for different modes for a terminal, or
for different user preferences. More than one use capabil-
ity may be given.
PART 2: PRINTER CAPABILITIES
The terminfo database allows you to define capabilities of
printers as well as terminals. To find out what capabili-
ties are available for printers as well as for terminals,
see the two lists under "DEVICE CAPABILITIES" that list
capabilities by variable and by capability name.
Section 2-1: Rounding Values
Because parameterized string capabilities work only with
integer values, we recommend that terminfo designers create
strings that expect numeric values that have been rounded.
Application designers should note this and should always
round values to the nearest integer before using them with a
parameterized string capability.
Section 2-2: Printer Resolution
A printer's resolution is defined to be the smallest spacing
of characters it can achieve. In general printers have
independent resolution horizontally and vertically. Thus
the vertical resolution of a printer can be determined by
measuring the smallest achievable distance between consecu-
tive printing baselines, while the horizontal resolution can
be determined by measuring the smallest achievable distance
between the left-most edges of consecutive printed, identi-
cal, characters. All printers are assumed to be capable of
printing with a uniform horizontal and vertical resolution.
The view of printing that terminfo currently presents is one
of printing inside a uniform matrix: All characters are
printed at fixed positions relative to each ``cell'' in the
matrix; furthermore, each cell has the same size given by
the smallest horizontal and vertical step sizes dictated by
the resolution. (The cell size can be changed as will be
seen later.) Many printers are capable of ``proportional
printing,'' where the horizontal spacing depends on the size
of the character last printed. terminfo does not make use
of this capability, although it does provide enough capabil-
ity definitions to allow an application to simulate propor-
tional printing. A printer must not only be able to print
characters as close together as the horizontal and vertical
resolutions suggest, but also of ``moving'' to a position an
integral multiple of the smallest distance away from a
26
N() MISC. REFERENCE MANUAL PAGES N()
previous position. Thus printed characters can be spaced
apart a distance that is an integral multiple of the smal-
lest distance, up to the length or width of a single page.
Some printers can have different resolutions depending on
different ``modes.'' In ``normal mode,'' the existing ter-
minfo capabilities are assumed to work on columns and lines,
just like a video terminal. Thus the old lines capability
would give the length of a page in lines, and the cols capa-
bility would give the width of a page in columns. In
``micro mode,'' many terminfo capabilities work on incre-
ments of lines and columns. With some printers the micro
mode may be concomitant with normal mode, so that all the
capabilities work at the same time.
Section 2-3: Specifying Printer Resolution'
The printing resolution of a printer is given in several
ways. Each specifies the resolution as the number of smal-
lest steps per distance:
Specification of Printer Resolution
Characteristic Number of Smallest Steps
_______________________________________
orhi Steps per inch horizontally
orvi Steps per inch vertically
orc Steps per column
orl Steps per line
When printing in normal mode, each character printed causes
movement to the next column, except in special cases
described later; the distance moved is the same as the per-
column resolution. Some printers cause an automatic move-
ment to the next line when a character is printed in the
rightmost position; the distance moved vertically is the
same as the per-line resolution. When printing in micro
mode, these distances can be different, and may be zero for
some printers.
Specification of Printer Resolution
Automatic Motion after Printing
___________________________________
Normal Mode:
orc Steps moved horizontally
orl Steps moved vertically
Micro Mode:
mcs Steps moved horizontally
mls Steps moved vertically
Some printers are capable of printing wide characters. The
distance moved when a wide character is printed in normal
mode may be different from when a regular width character is
printed. The distance moved when a wide character is
printed in micro mode may also be different from when a reg-
ular character is printed in micro mode, but the differences
are assumed to be related: If the distance moved for a
27
N() MISC. REFERENCE MANUAL PAGES N()
regular character is the same whether in normal mode or
micro mode (mcs=orc), then the distance moved for a wide
character is also the same whether in normal mode or micro
mode. This doesn't mean the normal character distance is
necessarily the same as the wide character distance, just
that the distances don't change with a change in normal to
micro mode. However, if the distance moved for a regular
character is different in micro mode from the distance moved
in normal mode (mcs<orc), the micro mode distance is assumed
to be the same for a wide character printed in micro mode,
as the table below shows.
Specification of Printer Resolution
Automatic Motion after Printing Wide Character
______________________________________________
Normal Mode or Micro Mode (mcs = orc):
widcs Steps moved horizontally
Micro Mode (mcs < orc):
mcs Steps moved horizontally
There may be control sequences to change the number of
columns per inch (the character pitch) and to change the
number of lines per inch (the line pitch). If these are
used, the resolution of the printer changes, but the type of
change depends on the printer:
Specification of Printer Resolution
Changing the Character/Line Pitches
______________________________________________________
cpi Change character pitch
cpix If set, cpi changes orhi, otherwise changes orc
lpi Change line pitch
lpix If set, lpi changes orvi, otherwise changes orl
chr Change steps per column
cvr Change steps per line
The cpi and lpi string capabilities are each used with a
single argument, the pitch in columns (or characters) and
lines per inch, respectively. The chr and cvr string capa-
bilities are each used with a single argument, the number of
steps per column and line, respectively. Using any of the
control sequences in these strings will imply a change in
some of the values of orc, orhi, orl, and orvi. Also, the
distance moved when a wide character is printed, widcs,
changes in relation to orc. The distance moved when a char-
acter is printed in micro mode, mcs, changes similarly, with
one exception: if the distance is 0 or 1, then no change is
assumed (see items marked with † in the following table).
Programs that use cpi, lpi, chr, or cvr should recalculate
the printer resolution (and should recalculate other values
see "Effect of Changing Printing Resolution" under "Dot-
Mapped Graphics").
Specification of Printer Resolution
Effects of Changing the Character/Line Pitches
_______________________________________________
28
N() MISC. REFERENCE MANUAL PAGES N()
Before After
_______________________________________________
Using cpi with cpix clear:
orhi' orhiorhi
U
or
sc
i'
ng cpi with cpix set: orc=Vcpi
orhi' orhi=orc.Vcpi
orc' orc
Using lpi with lpix clear:
orvi' orviorvi
U
or
si
l'
ng lpi with lpix set: orl=Vlpi
orvi' orvi=orl.Vlpi
orl' orl
Using chr:
orhi' orhi
orc' Vchr
Using cvr:
orvi' orvi
orl' Vcvr
Using cpi or chr: _orc_orc
m
wc
id
s'
cs' m
wc
id
s=
cm
s=
cs
w'
id
oc
rc
s'orc'
Vcpi, Vlpi, Vchr, and Vcvr are the arguments used with cpi,
lpi, chr, and cvr, respectively. The prime marks (') indi-
cate the old values.
Section 2-4: Capabilities that Cause Movement
In the following descriptions, ``movement'' refers to the
motion of the ``current position.'' With video terminals
this would be the cursor; with some printers this is the
carriage position. Other printers have different
equivalents. In general, the current position is where a
character would be displayed if printed. terminfo has
string capabilities for control sequences that cause move-
ment a number of full columns or lines. It also has
equivalent string capabilities for control sequences that
cause movement a number of smallest steps.
String Capabilities for Motion
__________________________________
mcub1 Move 1 step left
mcuf1 Move 1 step right
mcuu1 Move 1 step up
mcud1 Move 1 step down
mcub Move N steps left
mcuf Move N steps right
mcuu Move N steps up
mcud Move N steps down
mhpa Move N steps from the left
mvpa Move N steps from the top
The latter six strings are each used with a single argument,
29
N() MISC. REFERENCE MANUAL PAGES N()
N. Sometimes the motion is limited to less than the width
or length of a page. Also, some printers don't accept abso-
lute motion to the left of the current position. terminfo
has capabilities for specifying these limits.
Limits to Motion
__________________________________________________
mjump Limit on use of mcub1, mcuf1, mcuu1, mcud1
maddr Limit on use of mhpa, mvpa
xhpa If set, hpa and mhpa can't move left
xvpa If set, vpa and mvpa can't move up
If a printer needs to be in a ``micro mode'' for the motion
capabilities described above to work, there are string capa-
bilities defined to contain the control sequence to enter
and exit this mode. A boolean is available for those
printers where using a carriage return causes an automatic
return to normal mode.
Entering/Exiting Micro Mode
_________________________________
smicm Enter micro mode
rmicm Exit micro mode
crxm Using cr exits micro mode
The movement made when a character is printed in the right-
most position varies among printers. Some make no movement,
some move to the beginning of the next line, others move to
the beginning of the same line. terminfo has boolean capa-
bilities for describing all three cases.
What Happens After Character
Printed in Rightmost Position
______________________________________________
sam Automatic move to beginning of same line
Some printers can be put in a mode where the normal direc-
tion of motion is reversed. This mode can be especially
useful when there are no capabilities for leftward or upward
motion, because those capabilities can be built from the
motion reversal capability and the rightward or downward
motion capabilities. It is best to leave it up to an appli-
cation to build the leftward or upward capabilities, though,
and not enter them in the terminfo database. This allows
several reverse motions to be strung together without inter-
vening wasted steps that leave and reenter reverse mode.
Entering/Exiting Reverse Modes
___________________________________________
slm Reverse sense of horizontal motions
rlm Restore sense of horizontal motions
sum Reverse sense of vertical motions
rum Restore sense of vertical motions
While sense of horizontal motions reversed:
mcub1 Move 1 step right
mcuf1 Move 1 step left
mcub Move N steps right
mcuf Move N steps left
cub1 Move 1 column right
30
N() MISC. REFERENCE MANUAL PAGES N()
cuf1 Move 1 column left
cub Move N columns right
cuf Move N columns left
While sense of vertical motions reversed:
mcuu1 Move 1 step down
mcud1 Move 1 step up
mcuu Move N steps down
mcud Move N steps up
cuu1 Move 1 line down
cud1 Move 1 line up
cuu Move N lines down
cud Move N lines up
The reverse motion modes should not affect the mvpa and mhpa
absolute motion capabilities. The reverse vertical motion
mode should, however, also reverse the action of the line
``wrapping'' that occurs when a character is printed in the
right-most position. Thus printers that have the standard
terminfo capability am defined should experience motion to
the beginning of the previous line when a character is
printed in the right-most position under reverse vertical
motion mode. The action when any other motion capabilities
are used in reverse motion modes is not defined; thus, pro-
grams must exit reverse motion modes before using other
motion capabilities. Two miscellaneous capabilities com-
plete the list of new motion capabilities. One of these is
needed for printers that move the current position to the
beginning of a line when certain control characters, such as
``line-feed'' or ``form-feed,'' are used. The other is used
for the capability of suspending the motion that normally
occurs after printing a character.
Miscellaneous Motion Strings
________________________________________________________________
docr List of control characters causing cr
zerom Prevent auto motion after printing next single character
Margins
terminfo provides two strings for setting margins on termi-
nals: one for the left and one for the right margin.
Printers, however, have two additional margins, for the top
and bottom margins of each page. Furthermore, some printers
require not using motion strings to move the current posi-
tion to a margin and then fixing the margin there, but
require the specification of where a margin should be
regardless of the current position. Therefore terminfo
offers six additional strings for defining margins with
printers.
Setting Margins
__________________________________________
smgl Set left margin at current column
smgr Set right margin at current column
smgb Set bottom margin at current line
31
N() MISC. REFERENCE MANUAL PAGES N()
smgt Set top margin at current line
smgbp Set bottom margin at line N
smglp Set left margin at column N
smgrp Set right margin at column N
smgtp Set top margin at line N
The last four strings are used with one or more arguments
that give the position of the margin or margins to set. If
both of smglp and smgrp are set, each is used with a single
argument, N, that gives the column number of the left and
right margin, respectively. If both of smgtp and smgbp are
set, each is used to set the top and bottom margin, respec-
tively: smgtp is used with a single argument, N, the line
number of the top margin; however, smgbp is used with two
arguments, N and M, that give the line number of the bottom
margin, the first counting from the top of the page and the
second counting from the bottom. This accommodates the two
styles of specifying the bottom margin in different manufac-
turers' printers. When coding a terminfo entry for a
printer that has a settable bottom margin, only the first or
second parameter should be used, depending on the printer.
When writing an application that uses smgbp to set the bot-
tom margin, both arguments must be given. If only one of
smglp and smgrp is set, then it is used with two arguments,
the column number of the left and right margins, in that
order. Likewise, if only one of smgtp and smgbp is set,
then it is used with two arguments that give the top and
bottom margins, in that order, counting from the top of the
page. Thus when coding a terminfo entry for a printer that
requires setting both left and right or top and bottom mar-
gins simultaneously, only one of smglp and smgrp or smgtp
and smgbp should be defined; the other should be left blank.
When writing an application that uses these string capabili-
ties, the pairs should be first checked to see if each in
the pair is set or only one is set, and should then be used
accordingly. In counting lines or columns, line zero is the
top line and column zero is the left-most column. A zero
value for the second argument with smgbp means the bottom
line of the page.
All margins can be cleared with mgc.
Shadows, Italics, Wide Characters, Superscripts, Subscripts
Five new sets of strings are used to describe the capabili-
ties printers have of enhancing printed text.
Enhanced Printing
____________________________________________________
sshm Enter shadow-printing mode
rshm Exit shadow-printing mode
sitm Enter italicizing mode
ritm Exit italicizing mode
swidm Enter wide character mode
rwidm Exit wide character mode
32
N() MISC. REFERENCE MANUAL PAGES N()
ssupm Enter superscript mode
rsupm Exit superscript mode
supcs List of characters available as superscripts
ssubm Enter subscript mode
rsubm Exit subscript mode
subcs List of characters available as subscripts
If a printer requires the sshm control sequence before every
character to be shadow-printed, the rshm string is left
blank. Thus programs that find a control sequence in sshm
but none in rshm should use the sshm control sequence before
every character to be shadow-printed; otherwise, the sshm
control sequence should be used once before the set of char-
acters to be shadow-printed, followed by rshm. The same is
also true of each of the sitm/ritm, swidm/rwidm,
ssupm/rsupm, and ssubm/ rsubm pairs. Note that terminfo
also has a capability for printing emboldened text (bold).
While shadow printing and emboldened printing are similar in
that they ``darken'' the text, many printers produce these
two types of print in slightly different ways. Generally,
emboldened printing is done by overstriking the same charac-
ter one or more times. Shadow printing likewise usually
involves overstriking, but with a slight movement up and/or
to the side so that the character is ``fatter.'' It is
assumed that enhanced printing modes are independent modes,
so that it would be possible, for instance, to shadow print
italicized subscripts. As mentioned earlier, the amount of
motion automatically made after printing a wide character
should be given in widcs. If only a subset of the printable
ASCII characters can be printed as superscripts or sub-
scripts, they should be listed in supcs or subcs strings,
respectively. If the ssupm or ssubm strings contain control
sequences, but the corresponding supcs or subcs strings are
empty, it is assumed that all printable ASCII characters are
available as superscripts or subscripts. Automatic motion
made after printing a superscript or subscript is assumed to
be the same as for regular characters. Thus, for example,
printing any of the following three examples will result in
equivalent motion:
Bi Bi Bi
Note that the existing msgr boolean capability describes
whether motion control sequences can be used while in
``standout mode.'' This capability is extended to cover the
enhanced printing modes added here. msgr should be set for
those printers that accept any motion control sequences
without affecting shadow, italicized, widened, superscript,
or subscript printing. Conversely, if msgr is not set, a
program should end these modes before attempting any motion.
Section 2-5: Alternate Character Sets
In addition to allowing you to define line graphics
(described in Section 1-12), terminfo lets you define alter-
nate character sets. The following capabilities cover
33
N() MISC. REFERENCE MANUAL PAGES N()
printers and terminals with multiple selectable or definable
character sets.
Alternate Character Sets
_________________________________________________________
scs Select character set N
scsd Start definition of character set N, M characters
defc Define character A, B dots wide, descender D
rcsd End definition of character set N
csnm List of character set names
daisy Printer has manually changed print-wheels
The scs, rcsd, and csnm strings are used with a single argu-
ment, N, a number from 0 to 63 that identifies the character
set. The scsd string is also used with the argument N and
another, M, that gives the number of characters in the set.
The defc string is used with three arguments: A gives the
ASCII code representation for the character, B gives the
width of the character in dots, and D is zero or one depend-
ing on whether the character is a ``descender'' or not. The
defc string is also followed by a string of ``image-data''
bytes that describe how the character looks (see below).
Character set 0 is the default character set present after
the printer has been initialized. Not every printer has 64
character sets, of course; using scs with an argument that
doesn't select an available character set should cause a
null result from tparm. If a character set has to be
defined before it can be used, the scsd control sequence is
to be used before defining the character set, and the rcsd
is to be used after. They should also cause a null result
from tparm when used with an argument N that doesn't apply.
If a character set still has to be selected after being
defined, the scs control sequence should follow the rcsd
control sequence. By examining the results of using each of
the scs, scsd, and rcsd strings with a character set number
in a call to tparm, a program can determine which of the
three are needed. Between use of the scsd and rcsd strings,
the defc string should be used to define each character. To
print any character on printers covered by terminfo, the
ASCII code is sent to the printer. This is true for charac-
ters in an alternate set as well as ``normal'' characters.
Thus the definition of a character includes the ASCII code
that represents it. In addition, the width of the character
in dots is given, along with an indication of whether the
character should descend below the print line (such as the
lower case letter ``g'' in most character sets). The width
of the character in dots also indicates the number of
image-data bytes that will follow the defc string. These
image-data bytes indicate where in a dot-matrix pattern ink
should be applied to ``draw'' the character; the number of
these bytes and their form are defined below under ``Dot-
Mapped Graphics.'' It's easiest for the creator of terminfo
entries to refer to each character set by number; however,
these numbers will be meaningless to the application
34
N() MISC. REFERENCE MANUAL PAGES N()
developer. The csnm string alleviates this problem by pro-
viding names for each number. When used with a character
set number in a call to tparm, the csnm string will produce
the equivalent name. These names should be used as a refer-
ence only. No naming convention is implied, although anyone
who creates a terminfo entry for a printer should use names
consistent with the names found in user documents for the
printer. Application developers should allow a user to
specify a character set by number (leaving it up to the user
to examine the csnm string to determine the correct number),
or by name, where the application examines the csnm string
to determine the corresponding character set number. These
capabilities are likely to be used only with dot-matrix
printers. If they are not available, the strings should not
be defined. For printers that have manually changed print-
wheels or font cartridges, the boolean daisy is set.
Section 2-6: Dot-Matrix Graphics
Dot-matrix printers typically have the capability of repro-
ducing ``raster-graphics'' images. Three new numeric capa-
bilities and three new string capabilities can help a pro-
gram draw raster-graphics images independent of the type of
dot-matrix printer or the number of pins or dots the printer
can handle at one time.
Dot-Matrix Graphics
_______________________________________________________
npins Number of pins, N, in print-head
spinv Spacing of pins vertically in pins per inch
spinh Spacing of dots horizontally in dots per inch
porder Matches software bits to print-head pins
sbim Start printing bit image graphics, B bits wide
rbim End printing bit image graphics
The sbim sring is used with a single argument, B, the width
of the image in dots. The model of dot-matrix or raster-
graphics that terminfo presents is similar to the technique
used for most dot-matrix printers: each pass of the
printer's print-head is assumed to produce a dot-matrix that
is N dots high and B dots wide. This is typically a wide,
squat, rectangle of dots. The height of this rectangle in
dots will vary from one printer to the next; this is given
in the npins numeric capability. The size of the rectangle
in fractions of an inch will also vary; it can be deduced
from the spinv and spinh numeric capabilities. With these
three values an application can divide a complete raster-
graphics image into several horizontal strips, perhaps
interpolating to account for different dot spacing verti-
cally and horizontally. The sbim and rbim strings are used
to start and end a dot-matrix image, respectively. The sbim
string is used with a single argument that gives the width
of the dot-matrix in dots. A sequence of ``image-data
bytes'' are sent to the printer after the sbim string and
before the rbim string. The number of bytes is a integral
35
N() MISC. REFERENCE MANUAL PAGES N()
multiple of the width of the dot-matrix; the multiple and
the form of each byte is determined by the porder string as
described below. The porder string is a comma separated
list of pin numbers optionally followed by an numerical
offset. The offset, if given, is separated from the list
with a semicolon. The position of each pin number in the
list corresponds to a bit in an 8-bit data byte. The pins
are numbered consecutively from 1 to npins, with 1 being the
top pin. Note that the term ``pin'' is used loosely here;
``ink-jet'' dot-matrix printers don't have pins, but can be
considered to have an equivalent method of applying a single
dot of ink to paper. The bit positions in porder are in
groups of 8, with the first position in each group the most
significant bit and the last position the least significant
bit. An application produces 8-bit bytes in the order of
the groups in porder. An application computes the ``image-
data bytes'' from the internal image, mapping vertical dot
positions in each print-head pass into 8-bit bytes, using a
1 bit where ink should be applied and 0 where no ink should
be applied. This can be reversed (0 bit for ink, 1 bit for
no ink) by giving a negative pin number. If a position is
skipped in porder, a 0 bit is used. If a position has a
lower case `x' instead of a pin number, a 1 bit is used in
the skipped position. For consistency, a lower case `o' can
be used to represent a 0 filled, skipped bit. There must be
a multiple of 8 bit positions used or skipped in porder; if
not, 0 bits are used to fill the last byte in the least sig-
nificant bits. The offset, if given, is added to each data
byte; the offset can be negative. Some examples may help
clarify the use of the porder string. The AT&T 470, AT&T
475 and C.Itoh 8510 printers provide eight pins for graph-
ics. The pins are identified top to bottom by the 8 bits in
a byte, from least significant to most. The porder strings
for these printers would be 8,7,6,5,4,3,2,1. The AT&T 478
and AT&T 479 printers also provide eight pins for graphics.
However, the pins are identified in the reverse order. The
porder strings for these printers would be 1,2,3,4,5,6,7,8.
The AT&T 5310, AT&T 5320, DEC LA100, and DEC LN03 printers
provide six pins for graphics. The pins are identified top
to bottom by the decimal values 1, 2, 4, 8, 16 and 32.
These correspond to the low six bits in an 8-bit byte,
although the decimal values are further offset by the value
63. The porder string for these printers would be
,,6,5,4,3,2,1;63, or alternately o,o,6,5,4,3,2,1;63.
Section 2-7: Effect of Changing Printing Resolution
If the control sequences to change the character pitch or
the line pitch are used, the pin or dot spacing may change:
Dot-Matrix Graphics
Changing the Character/Line Pitches
___________________________________
cpi Change character pitch
36
N() MISC. REFERENCE MANUAL PAGES N()
cpix If set, cpi changes spinh
lpi Change line pitch
lpix If set, lpi changes spinv
Programs that use cpi or lpi should recalculate the dot
spacing:
Dot-Matrix Graphics
Effects of Changing the Character/Line Pitches
_________________________________________________
Before After
_________________________________________________
37
() MISC. REFERENCE MANUAL PAGES ()
Using cpi with cpix clear:
spinh' spinh
Using cpi with cpix set: _orhi
U
sp
sing
h'lpi with lpix clear: spinh=spinh'.orhi'
spinv' spinv
Using lpi with lpix set: _orhi
U
sp
sing
v'chr: spinv=spinv'.orhi'
spinh' spinh
Using cvr:
spinv' spinv
orhi' and orhi are the values of the horizontal resolution
in steps per inch, before using cpi and after using cpi,
respectively. Likewise, orvi' and orvi are the values of
the vertical resolution in steps per inch, before using lpi
and after using lpi, respectively. Thus, the changes in the
dots per inch for dot-matrix graphics follow the changes in
steps per inch for printer resolution.
Section 2-8: Print Quality
Many dot-matrix printers can alter the dot spacing of
printed text to produce near ``letter quality'' printing or
``draft quality'' printing. Usually it is important to be
able to choose one or the other because the rate of printing
generally falls off as the quality improves. There are
three new strings used to describe these capabilities.
Print Quality
_____________________________________
snlq Set near-letter quality print
snrmq Set normal quality print
sdrfq Set draft quality print
The capabilities are listed in decreasing levels of quality.
If a printer doesn't have all three levels, one or two of
the strings should be left blank as appropriate.
Section 2-9: Printing Rate and Buffer Size
Because there is no standard protocol that can be used to
keep a program synchronized with a printer, and because
modern printers can buffer data before printing it, a pro-
gram generally cannot determine at any time what has been
printed. Two new numeric capabilities can help a program
estimate what has been printed.
Print Rate/Buffer Size
___________________________________________________
cps Nominal print rate in characters per second
bufsz Buffer capacity in characters
cps is the nominal or average rate at which the printer
prints characters; if this value is not given, the rate
should be estimated at one-tenth the prevailing baud rate.
bufsz is the maximum number of subsequent characters buf-
fered before the guaranteed printing of an earlier
1
() MISC. REFERENCE MANUAL PAGES ()
character, assuming proper flow control has been used. If
this value is not given it is assumed that the printer does
not buffer characters, but prints them as they are received.
As an example, if a printer has a 1000-character buffer,
then sending the letter ``a'' followed by 1000 additional
characters is guaranteed to cause the letter ``a'' to print.
If the same printer prints at the rate of 100 characters per
second, then it should take 10 seconds to print all the
characters in the buffer, less if the buffer is not full.
By keeping track of the characters sent to a printer, and
knowing the print rate and buffer size, a program can syn-
chronize itself with the printer. Note that most printer
manufacturers advertise the maximum print rate, not the nom-
inal print rate. A good way to get a value to put in for
cps is to generate a few pages of text, count the number of
printable characters, and then see how long it takes to
print the text. Applications that use these values should
recognize the variability in the print rate. Straight text,
in short lines, with no embedded control sequences will
probably print at close to the advertised print rate and
probably faster than the rate in cps. Graphics data with a
lot of control sequences, or very long lines of text, will
print at well below the advertised rate and below the rate
in cps. If the application is using cps to decide how long
it should take a printer to print a block of text, the
application should pad the estimate. If the application is
using cps to decide how much text has already been printed,
it should shrink the estimate. The application will thus
err in favor of the user, who wants, above all, to see all
the output in its correct place.
FILES
/usr/share/lib/terminfo/?/* compiled terminal descrip-
tion database
/usr/share/lib/.COREterm/?/* subset of compiled terminal
description database
/usr/share/lib/tabset/* tab settings for some termi-
nals, in a format appropri-
ate to be output to the ter-
minal (escape sequences that
set margins and tabs)
SEE ALSO
curses(3X), ls(1), pg(1), printf(3S), stty(1), tic(1M),
tput(1), tty(1), vi(1).
NOTES
The most effective way to prepare a terminal description is
by imitating the description of a similar terminal in ter-
minfo and to build up a description gradually, using partial
descriptions with a screen oriented editor, such as vi, to
check that they are correct. To easily test a new terminal
2
() MISC. REFERENCE MANUAL PAGES ()
description the environment variable TERMINFO can be set to
the pathname of a directory containing the compiled descrip-
tion, and programs will look there rather than in
/usr/share/lib/terminfo.
3