xntpdc(ADMN) 19 June 1992 xntpdc(ADMN) Name xntpdc - query/control program for the Network Time Protocol daemon Syntax xntpdc [-ilnps] [-c command] [host] [...] Description xntpdc is used to query the xntpd(ADMN) daemon about its current state and to request changes in that state. The program may be run either in interactive mode or controlled using command line arguments. Extensive state and statistics information is available through the xntpdc inter- face. In addition, nearly all the configuration options which can be specified at startup using xntpd's configuration file may also be speci- fied at runtime using xntpdc. If one or more request options is included on the command line when xntpdc is executed, each of the requests will be sent to the NTP servers running on each of the hosts given as command line arguments, or on localhost by default. If no request options are given, xntpdc will attempt to read commands from the standard input and execute these on the NTP server running on the first host given on the command line, again defaulting to localhost when no other host is specified. xntpdc will prompt for commands if the standard input is a terminal device. xntpdc uses NTP mode 7 packets to communicate with the NTP server, and hence can be used to query any compatible server on the network which permits it. Note that since NTP is a UDP protocol this communication will be somewhat unreliable, especially over large distances in terms of network topology. xntpdc makes no attempt to retransmit requests, and will time requests out if the remote host is not heard from within a suitable time out time. Command line options are described following. Specifying a command line option other than -i or -n will cause the specified query (queries) to be sent to the indicated host(s) immediately. Otherwise, xntpdc will attempt to read interactive format commands from the standard input. -c The following argument is interpreted as an interactive format com- mand and is added to the list of commands to be executed on the specified host(s). Multiple -c options may be given. -i Force xntpdc to operate in interactive mode. Prompts will be written to the standard output and commands read from the standard input. -l Obtain a list of peers which are known to the server(s). This switch is equivalent to -c listpeers. -n Output all host addresses in dotted-quad numeric format rather than converting to the canonical host names. -p Print a list of the peers known to the server as well as a summary of their state. This is equivalent to -c peers. -s Print a list of the peers known to the server as well as a summary of their state, but in a slightly different format than the -p switch. This is equivalent to -c dmpeers. Internal commands Interactive format commands consist of a keyword followed by zero to four arguments. Only enough characters of the full keyword to uniquely iden- tify the command need be typed. The output of a command is normally sent to the standard output, but optionally the output of individual commands may be sent to a file by appending a``>'', followed by a file name, to the command line. A number of interactive format commands are executed entirely within the xntpdc program itself and do not result in NTP mode 7 requests being sent to a server. These are described following. ? A ``?'' by itself will print a list of all the command keywords known to this incarnation of xntpdc. A ``?'' followed by a command keyword will print function and usage information about the command. help [commandkeyword] A synonym for the s command. timeout milliseconds Specify a time out period for responses to server queries. The default is about 8000 milliseconds. delay milliseconds Specify a time interval to be added to timestamps included in requests which require authentication. This is used to enable (unreliable) server reconfiguration over long delay network paths or between machines whose clocks are unsynchronized. host hostname Set the host to which future queries will be sent. hostname may be either a host name or a numeric address. poll [#] [verbose] Poll the current server in client mode. The first argument is the number of times to poll (default is 1) while the second argument may be given to obtain a more detailed output of the results. This command is currently just unsupported. keyid # This command allows the specification of a key number to be used to authenticate configuration requests. This must corre- spond to the key number the server has been configured to use for this purpose. passwd This command prompts you to type in a password (which will not be echoed) which will be used to authenticate configuration requests. The password must correspond to the key configured for use by theNTP server for this purpose if such requests are to be successful. hostnames yes|no If yes is specified, host names are printed in information dis- plays. If no is given, numeric addresses are printed instead. The default is yes unless modified using the command line -n switch. quit Exit xntpdc. Query commands Query commands result in NTP mode 7 packets containing requests for in- formation being sent to the server. These are ``read-only'' commands in that they make no modification of the server configuration state. listpeers Obtain and print a brief list of the peers for which the server is maintaining state. These should include all configured peer associations as well as those peers whose stratum is such that they are considered by the server to be possible future syn- chronization candidates. peers Obtain a list of peers for which the server is maintaining state, along with a summary of that state. Summary information includes the address of the remote peer, the local interface address (0.0.0.0 if a local address has yet to be determined), the stratum of the remote peer (a stratum of 16 indicates the remote peer is unsynchronized), the polling interval, in seconds, the reachability register, in octal, and the current estimated delay, offset and dispersion of the peer, all in seconds. In addition, the character in the left margin indi- cates the mode this peer entry is operating in. A ``+'' denotes symmetric active, a ``-'' indicates symmetric passive, a ``='' means the remote server is being polled in client mode, a ``^'' indicates that the server is broadcasting to this address, a ``~'' denotes that the remote peer is sending broad- casts and a ``*'' marks the peer the server is currently syn- chronizing to. dmpeers A slightly different peer summary list. Identical to the out- put of the peers command except for the character in the left- most column. Characters only appear beside peers which were included in the final stage of the clock selection algorithm. A ``.'' indicates that this peer was cast off in the falset- icker detection, while a ``+'' indicates that the peer made it through. A ``*'' denotes the peer the server is currently syn- chronizing with. showpeer peeraddress [addr2] [addr3] [addr4] Shows a detailed display of the current peer variables for one or more peers. Most of these values are described in the NTP Version 2 specification. pstats peeraddress [addr2] [addr3] [addr4] Show per-peer statistic counters associated with the specified peer(s). loopinfo [oneline|multiline] Print the values of selected loop filter variables. The loop filter is the part of NTP which deals with adjusting the local system clock. The ``offset'' is the last offset given to the loop filter by the packet processing code. The ``frequency'' is actually the frequency error, or drift, of your system's clock in the units NTP uses for internal computations. Divid- ing this number by 4096 should give you the actual drift rate. The ``compliance'' is actually a long term average offset and is used by NTP to control the gain of the loop filter. The ``timer'' value is the number of seconds which have elapsed since a new sample offset was given to the loop filter. The ``oneline'' and ``multiline'' options specify the format in which this information is to be printed. ``multiline'' is the default. sysinfo Print a variety of system state variables, i.e. state related to the local server. Many of these values are described in the NTP Version 2 specification, RFC 1119. sysstats Print a number of stat counters maintained in the protocol module. memstats Print a number of counters related to the peer memory alloca- tion code. iostats Print counters maintained in the input-output module. timerstats Print counters maintained in the timer/event queue support code. reslist Obtain and print the server's restriction list. This list is (usually) printed in sorted order and may help to understand how the restrictions are applied. monlist Obtain and print traffic counts collected and maintained by the monitor facility. clockinfo clockpeeraddress [addr2] [addr3] [addr4] Obtain and print information concerning a peer clock. The values obtained provide information on the setting of fudge factors and other clock performance information. clkbug clockpeeraddress [addr2] [addr3] [addr4] Obtain debugging information for a clock peer. This informa- tion is provided only by some clock drivers and is mostly undecodable without a copy of the driver source in hand. Runtime configuration requests All requests which cause state changes in the server are authenticated by the server using a configured NTP key (the facility can also be disabled by the server by not configuring a key). The key number and the corre- sponding key must also be made known to xtnpdc. This can be done using the keyid and passwd commands, the latter of which will prompt at the terminal for a password to use as the encryption key. You will also be prompted automatically for both the key number and password the first time a command which would result in an authenticated request to the server is given. Authentication not only provides verification that the requester has permission to make such changes, but also gives an extra degree of protection against transmission errors. Authenticated requests always include a timestamp in the packet data, which is included in the computation of the authentication code. This timestamp is compared by the server to its receive timestamp. If they differ by more than a small amount, the request is rejected. This is done for two reasons. First, it makes simple replay attacks on the server, by someone who might be able to overhear traffic on your LAN, much more difficult. Second, it makes it more difficult to request con- figuration changes to your server from topologically remote hosts. While the reconfiguration facility will work well with a server on the local host, and may work adequately between time-synchronized hosts on the same LAN, it will work very poorly for more distant hosts. As such, if rea- sonable passwords are chosen, care is taken in the distribution and pro- tection of keys and appropriate source address restrictions are applied, the runtime reconfiguration facility should provide an adequate level of security. The following commands all make authenticated requests. addpeer peeraddress [keyid] [version#] [minpoll] Add a configured, symmetric active peer association with a peer at the given address. If the optional keyid is a nonzero integer all outgoing packets to the remote server will have an authentication field attached encrypted with this key. If the value is 0 (or not given) no authentication will be done. The version# can be 1 or 2, and defaults to 2. If minpoll is specified the polling interval for the association will remain clamped at the minimum. The latter option is only useful for testing. Note that an existing association with the same peer may be deleted when this command is executed, or may simply be converted to conform to the new configuration, as appropriate. addserver peeraddress [keyid] [version#] [minpoll] Identical to the addpeer command except that polling is done in client mode rather than symmetric active mode. broadcast peeraddress [keyid] [version#] [minpoll] Identical to the addpeer command except that packets are instead sent in broadcast mode. The peeraddress parameter will generally be a broadcast address on one of your local net- works. unconfig peeraddress [addr2] [addr3] [addr4] This command causes the configured bit to be removed from the specified peer(s). In many cases this will cause the peer association to be deleted. When appropriate, however, the association may persist in an unconfigured mode if the remote peer is willing to continue on in this fashion. set bclient|auth [...] Allow the setting of the broadcast client and/or authenticate system flags. Setting the former causes the server to listen for broadcast NTP to synchronize to broadcasts when appropri- ate. Setting the latter flag causes the server to only syn- chronize with peers which include an authentication field encrypted with one of the local server's trusted keys. clear bclient|auth [...] Allow the broadcast client and/or authenticate system flags to be cleared. Clearing the former causes incoming broadcast NTP packets to be ignored. Clearing the latter allows peers which have not included an authentication field, or which have included one but have encrypted it with an untrusted key, to be considered synchronization candidates. restrict address mask flag [flag] Cause flag(s) to be added to an existing restrict list entry, or adds a new entry to the list with the specified flag(s). The possible choices for the flags arguments are given in the following list: ignore Ignore all packets from hosts which match this entry. If this flag is specified neither queries nor time server polls will be responded to. noquery Ignore all NTP mode 7 packets (that is, information queries and configuration requests) from the source. Time service is not affected. nomodify Ignore all NTP mode 7 packets which attempt to modify the state of the server (that is, runtime reconfigu- ration). Queries which return information are per- mitted. noserve Ignore NTP packets whose mode is other than 7. In effect, time service is denied, though queries may still be permitted. nopeer Provide stateless time service to polling hosts, but do not allocate peer memory resources to these hosts even if they otherwise might be considered useful as future synchronization partners. notrust Treat these hosts normally in other respects, but never use them as synchronization sources. ntpport This is actually a match algorithm modifier, rather than a restriction flag. Its presence causes the re- striction entry to be matched only if the source port in the packet is the standard NTP UDP port (123). Both ntpport and non-ntpport may be specified. The ntpport is considered more specific and is sorted later in the list. unrestrict address mask flag [flag] Remove the specified flag(s) from the restrict list entry indi- cated by the address and mask arguments. delrestrict address mask [ntpport] Delete the matching entry from the restrict list. monitor yes|no Enable or disable the monitoring facility. Note that a monitor no command followed by a monitor yes command is a good way of resetting the packet counts. readkeys Causes the current set of authentication keys to be purged and a new set to be obtained by rereading the keys file (which must have been specified in the xntpd configuration file). This allows encryption keys to be changed without restarting the server. trustkey keyid [keyid] [keyid] [keyid] Adds one or more keys to the trusted key list. When authenti- cation is enabled, peers whose time is to be trusted must be authenticated using a trusted key. untrustkey keyid [keyid] [keyid] [keyid] Removes one or more keys from the trusted key list. authinfo Returns information concerning the authentication module, including known keys and counts of encryptions and decryptions which have been done. setprecision precisionvalue Sets the precision which the server advertises to the specified value. This should be a negative integer in the range -4 through -20. setselect algorithmnumber Sets the selection weight algorithm to that indicated by the specified number. This should be an integer value between 1 and 5 inclusive. Algorithm 1 is that specified in RFC 1119, the other 4 algorithms are experimental and should be used with caution. See also xntpd(ADMN)