X Version 11 (1 September 1988) XDrawArc(XS)
NAME
XDrawArc, XDrawArcs - draw arcs
SYNTAX
XDrawArc(display, d, gc, x, y, width, height, angle1,
angle2)
Display *display;
Drawable d;
GC gc;
int x, y;
unsigned int width, height;
int angle1, angle2;
XDrawArcs(display, d, gc, arcs, narcs)
Display *display;
Drawable d;
GC gc;
XArc *arcs;
int narcs;
ARGUMENTS
angle1 Specifies the start of the arc relative to the
three-o'clock position from the center, in units
of degrees * 64.
angle2 Specifies the path and extent of the arc relative
to the start of the arc, in units of degrees * 64.
arcs Specifies a pointer to an array of arcs.
d Specifies the drawable.
display Specifies the connection to the X server.
gc Specifies the GC.
narcs Specifies the number of arcs in the array.
width
height Specify the width and height, which are the major
and minor axes of the arc.
x
y Specify the x and y coordinates, which are
relative to the origin of the drawable and specify
the upper-left corner of the bounding rectangle.
DESCRIPTION
XDrawArc draws a single circular or elliptical arc, and
XDrawArcs draws multiple circular or elliptical arcs. Each
arc is specified by a rectangle and two angles. The center
of the circle or ellipse is the center of the rectangle, and
the major and minor axes are specified by the width and
height. Positive angles indicate counterclockwise motion,
and negative angles indicate clockwise motion. If the
magnitude of angle2 is greater than 360 degrees, XDrawArc or
XDrawArcs truncates it to 360 degrees.
For an arc specified as
[ x, y, width, height, angle1, angle2], h
te
he
igh
or
t]
i,
gia
nnd
ofth
te
he
width, y+
i
ma
nf
ji
on
ria
te
nd
lymi
th
ni
on
r a
pa
xe
th
s d
ie
ssa
cr
ti[
bi
x+
ng the entire2circle or ellipse
2 height] and
intersects the horizontal axis at [x, y+
height] and intersects the ver2
tical axis at
[x+width, y+ width, y+height]. These coordinates can
width, y] an2
d [x+
[
be
x+fractional and so a2
re not truncated to discrete
coord2
inates. The path should be defined by the ideal
mathematical path. For a wide line with line-width lw, the
bounding outlines for filling are given by the two
infinitely thin paths consisting of all points whose
perpendicular distance from the path of the circle/ellipse
is equal to lw/2 (which may be a fractional value). The
cap-style and join-style are applied the same as for a line
corresponding to the tangent of the circle/ellipse at the
endpoint.
For an arc specified as
[ x, y, width, height, angle1, angle2], the angles must be
specified in the effectively skewed coordinate system of the
ellipse (for a circle, the angles and coordinate systems are
identical). The relationship between these angles and
angles expressed in the normal coordinate system of the
screen (as measured with a protractor) is as follows:
|
| _width|+adjust
skewed-angle = atan|tan(normal-angle)* |
The skewed-angle and norm
|al-angle are expreh
se
se
id
ghi
tn radians
(rather than in degrees scaled by 64) in the r]
ana
ge
nd[0
a,
dj2
u]
stai
nd
s:
_,
where atan returns a value in the range [- 2
2 _]
0 for normal-angle in the range [0, 3]
_, 2
for normal-angle in the range [3, 2]
2 for normal-angle in the range [2
2
For any given arc, XDrawArc and XDrawArcs do not draw a
pixel more than once. If two arcs join correctly and if the
line-width is greater than zero and the arcs intersect,
XDrawArc and XDrawArcs do not draw a pixel more than once.
Otherwise, the intersecting pixels of intersecting arcs are
drawn multiple times. Specifying an arc with one endpoint
and a clockwise extent draws the same pixels as specifying
the other endpoint and an equivalent counterclockwise
extent, except as it affects joins.
If the last point in one arc coincides with the first point
in the following arc, the two arcs will join correctly. If
the first point in the first arc coincides with the last
point in the last arc, the two arcs will join correctly. By
specifying one axis to be zero, a horizontal or vertical
line can be drawn. Angles are computed based solely on the
coordinate system and ignore the aspect ratio.
Both functions use these GC components: function, plane-
mask, line-width, line-style, cap-style, join-style, fill-
style, subwindow-mode, clip-x-origin, clip-y-origin, and
clip-mask. They also use these GC mode-dependent
components: foreground, background, tile, stipple, tile-
stipple-x-origin, tile-stipple-y-origin, dash-offset, and
dash-list.
XDrawArc and XDrawArcs can generate BadDrawable, BadGC, and
BadMatch errors.
DIAGNOSTICS
BadDrawable
A value for a Drawable argument does not name a
defined Window or Pixmap.
BadGC A value for a GContext argument does not name a
defined GContext.
BadMatch An InputOnly window is used as a Drawable.
BadMatch Some argument or pair of arguments has the correct
type and range but fails to match in some other
way required by the request.
SEE ALSO
XDrawLine(XS), XDrawPoint(XS), XDrawRectangle(XS)
Xlib - C Language X Interface
(printed 2/12/90) (1 September 1988) XDrawArc(XS)