Museum

Home

Lab Overview

Retrotechnology Articles

Online Manuals

⇒ xfsck(1M) — Dell System V Release 4 Issue 2.2

Media Vault

Software Library

Restoration Projects

Artifacts Sought

Related Articles

fsck(1M)



xfsck(1M)                 UNIX System V(Base System)                  xfsck(1M)


NAME
      xfsck - check and repair XENIX filesystems

SYNOPSIS
      /bin/xfsck [options] [filesystem] ...

DESCRIPTION
      The xfsck command audits and interactively repairs inconsistent
      conditions for XENIX System V filesystems.  If the filesystem is
      consistent, then xfsck reports number of files, number of blocks used,
      and number of blocks free.  If the filesystem is inconsistent, the user
      is prompted whether or not xfsck should proceed with each correction.  It
      should be noted that most corrective actions result in some loss of data.
      The amount and severity of the loss can be determined from the diagnostic
      output.  If the user does not have write permission, xfsck defaults to
      the  action of the -n option.

      The xfsck options are:

      -y      Assumes a response to all questions asked by xfsck.

      -n      Assumes a response to all questions asked by xfsck.  This option
              does not open the filesystem for writing.

      -s b:c  Ignores the actual free list and unconditionally reconstructs a
              new one by rewriting the super-block of the filesystem. The
              filesystem must be unmounted while this is done.

              This option allows for creating an optimal free-list
              organization.  The following forms are supported:
                -s
                -sBlocks-per-cylinder:Blocks-to-skip (filesystem interleave)

              If b:c is not given, then the values that were used when the
              filesystem was created are used again.  If these values were not
              specified, then the default value is used.

      -S      Conditionally reconstructs the free list.  This option is similar
              to -s b:c above, except that the free list is rebuilt only if
              there are no discrepancies discovered in the filesystem. The -S
              option forces a ``no'' response to all questions asked by xfsck.
              This option is useful for forcing free-list reorganization on
              uncontaminated filesystems.

      -t      Causes xfsck to use the next argument as the scratch file, if
              needed. A scratch file is used if xfsck cannot obtain enough
              memory to keep its tables.  Without the -t flag, xfsck prompts
              the user for the name of the scratch file. The file chosen should
              not be on the filesystem being checked. In addition, if the
              scratch file is not a special file or did not already exist, it
              is removed when xfsck completes.  Note that if the system has a
              large hard disk, there may not be enough space on another


10/89                                                                    Page 1







xfsck(1M)                 UNIX System V(Base System)                  xfsck(1M)


              filesystem for the scratch file.  In such cases, if the system
              has a floppy disk drive, use a blank, formatted floppy disk in
              the floppy disk drive with (for example) /dev/fd0 specified as
              the scratch file.

      -q      Causes xfsck to perform a quiet check.  Does not print size-check
              messages in Phase 1.  Unreferenced fifo5 files are selectively
              removed.  If xfsck requires it, counts in the superblock are
              automatically fixed and the free list salvaged.

      -D      Checks directories for bad blocks.  Use this option after the
              system crashes.

      -f      Causes xfsck to perform a fast check. xfsck checks block and
              sizes (Phase 1) and checks the free list (Phase 5).  The free
              list is reconstructed (Phase 6), if necessary.

      -rr     Recovers the root filesystem.  The required filesystem argument
              must refer to the root filesystem, and preferably to the block
              device (normally /dev/root ).  This switch implies -y (yes) and
              overrides -n (no).  If any modifications to the filesystem are
              required, the system will be automatically shutdown to ensure the
              integrity of the filesystem.

      -c      Causes any supported filesystem to be converted to the current
              filesystem type. The user is prompted to verify the conversion of
              each filesystem, unless the -y option is specified.  It is
              recommended that every filesystem be checked with this option
              while unmounted if it is to be used with the current version of
              XENIX.  To update the active root filesystem, check it with the
              following command line:
                   xfsck -c -rr /dev/root

      If no filesystems are specified, xfsck reads a list of default
      filesystems from the /etc/checklist file.

      The following are some of the inconsistencies xfsck checks for:

      -   Blocks claimed by more than one inode or the free list

      -   Blocks claimed by an inode or the free list outside the range of the
          filesystem

      -   Incorrect link counts

      -   Size checks:
            Incorrect number of blocks
            Directory size not 16-byte aligned

      -   Bad inode format




Page 2                                                                    10/89







xfsck(1M)                 UNIX System V(Base System)                  xfsck(1M)


      -   Blocks not accounted for anywhere

      -   Directory checks:
            File pointing to unallocated inode
            Inode number out of range

      -   Super block checks:
            More than 65536 inodes
            More blocks for inodes than there are in the filesystem

      -   Bad free block list format

      -   Total free block or free inode count incorrect

      With the user's consent, xfsck reconnects orphaned (allocated, but
      unreferenced) files and directories by placing them in the lost+found
      directory.  The file's (or directory's) inode number then becomes its
      name.  Note that the lost+found directory must already exist in the root
      of the filesystem being checked and must have empty slots in which
      entries can be made.  To create the lost+found directory, copy a few
      files to the directory, then remove them (before executing xfsck ).

FILES
      /etc/checklistContains default list of filesystems to check
      /etc/default/bootContains flags for automatic boot control

SEE ALSO
      fsck(1M)

NOTES
      xfsck will not run on a mounted non-raw filesystem, unless the filesystem
      is the root filesystem, or the -n option is specified and no writing out
      of the filesystem will take place.  If any such attempt is made, xfsck
      displays a warning and no further processing of the filesystem is done
      for the specified device.

      xfsck does not support filesystems created under XENIX-86 version 3.0
      because the word order in type long variables has changed.  However,
      xfsck is capable of auditing and repairing XENIX version 3.0 filesystems
      if the word ordering is correct.

      Run xfsck -rr /dev/root for the root filesystem. Run xfsck /dev/??  on
      the unmounted block device for all other filesystems.

      It is not recommended that users use xfsck on raw devices. Although
      checking a raw device is almost always faster, there is no way to tell if
      the filesystem is mounted.  If the filesystem is mounted, cleaning it
      will almost certainly result in an inconsistent superblock.






10/89                                                                    Page 3





Typewritten Software • bear@typewritten.org • Edmonds, WA 98026