TOP(1) UNIX System V(Local) TOP(1)
NAME
top - display and update information about the top cpu processes
SYNOPSIS
top [ -Sbinu ] [ -dcount ] [ -stime ] [ number ]
DESCRIPTION
Top displays the top processes on the system and periodically updates
this information. If standard output is an intelligent terminal (see
below) then as many processes as will fit on the terminal screen are
displayed by default. Otherwise, a good number of them are shown (around
20). Raw cpu percentage is used to rank the processes. If number is
given, then the top number processes will be displayed instead of the
default.
Top makes a distinction between terminals that support advanced
capabilities and those that do not. This distinction affects the choice
of defaults for certain options. In the remainder of this document, an
"intelligent" terminal is one that supports cursor addressing, clear
screen, and clear to end of line. Conversely, a "dumb" terminal is one
that does not support such features. If the output of top is redirected
to a file, it acts as if it were being run on a dumb terminal.
OPTIONS
-S Show system processes in the display. Normally, system processes
such as the pager and the swapper are not shown. This option makes
them visible.
-b Use "batch" mode. In this mode, all input from the terminal is
ignored. Interrupt characters (such as ^C and ^\) still have an
effect. This is the default on a dumb terminal, or when the output
is not a terminal.
-i Use "interactive" mode. In this mode, any input is immediately
read for processing. See the section on "Interactive Mode" for an
explanation of which keys perform what functions. After the
command is processed, the screen will immediately be updated, even
if the command was not understood. This mode is the default when
standard output is an intelligent terminal.
-n Use "non-interactive" mode. This is indentical to "batch" mode.
-u Do not take the time to map uid numbers to usernames. Normally,
top will read as much of the file "/etc/passwd" as is necessary to
map all the user id numbers it encounters into login names. This
option disables all that, while possibly decreasing execution time.
The uid numbers are displayed instead of the names.
-dcount
Show only count displays, then exit. A display is considered to be
one update of the screen. This option allows the user to select
the number of displays he wants to see before top automatically
10/89 Page 1
TOP(1) UNIX System V(Local) TOP(1)
exits. For intelligent terminals, no upper limit is set. The
default is 1 for dumb terminals.
-stime
Set the delay between screen updates to time seconds. The default
delay between updates is 10 seconds.
Both count and number fields can be specified as "infinite", indicating
that they can stretch as far as possible. This is accomplished by using
any proper prefix of the keywords "infinity", "maximum", or "all". The
default for count on an intelligent terminal is, in fact, infinity.
INTERACTIVE MODE
When top is running in "interactive mode", it reads commands from the
terminal and acts upon them accordingly. In this mode, the terminal is
put in "CBREAK", so that a character will be processed as soon as it is
typed. Almost always, a key will be pressed when top is between
displays; that is, while it is waiting for time seconds to elapse. If
this is the case, the command will be processed and the display will be
updated immediately thereafter (reflecting any changes that the command
may have specified). This happens even if the command was incorrect. If
a key is pressed while top is in the middle of updating the display, it
will finish the update and then process the command. Some commands
require additional information, and the user will be prompted
accordingly. While typing this information in, the user's erase and kill
keys (as set up by the command stty) are recognized, and a newline
terminates the input.
These commands are currently recognized (^L refers to control-L):
^L Redraw the screen.
h or ?
Display a summary of the commands (help screen).
q Quit top.
d Change the number of displays to show (prompt for new number).
Remember that the next display counts as one, so typing d1 will
make top show one final display and then immediately exit.
n or #
Change the number of processes to display (prompt for new number).
s Change the number of seconds to delay between displays (prompt for
new number).
k Send a signal ("kill" by default) to a list of processes. This
acts similarly to the command kill(1)).
Page 2 10/89
TOP(1) UNIX System V(Local) TOP(1)
r Change the priority (the "nice") of a list of processes. This acts
similarly to the command renice(8)).
e Display a list of system errors (if any) generated by the last kill
or renice command.
THE DISPLAY
The top few lines of the display show general information about the state
of the system, including the last process id assigned to a process, the
three load averages, the current time, the number of existing processes,
the number of processes in each state (sleeping, ABANDONED, running,
starting, zombies, and stopped), and a percentage of time spent in each
of the processor states (user, nice, system, and idle). It also includes
the amount of virtual and real memory in use (with the amount of memory
considered "active" in parentheses) and the amount of free memory.
The remainder of the screen displays information about individual
processes. This display is similar in spirit to ps(1) but it is not
exactly the same. PID is the process id, USERNAME is the name of the
process's owner (if -u is specified, a UID column will be substituted for
USERNAME), PRI is the current priority of the process, NICE is the nice
amount (in the range -20 to 20), SIZE is the total size of the process
(text, data, and stack), RES is the current amount of resident memory
(both SIZE and RES are given in kilobytes), STATE is the current state
(one of "sleep", "WAIT", "run", "idl", "zomb", or "stop"), TIME is the
number of system and user cpu seconds that the process has used, WCPU is
the weighted cpu percentage (this is the same value that ps(1) displays
as CPU), CPU is the raw percentage and is the field that is sorted to
determine the order of the processes, and COMMAND is the name of the
command that the process is currently running (if the process is swapped
out, this column is marked "<swapped>").
NOTES
The "ABANDONED" state (known in the kernel as "SWAIT") was abandoned,
thus the name. A process should never end up in this state.
AUTHOR
William LeFebvre, Rice University graduate student
FILES
/dev/kmem kernel memory
/dev/mem physical memory
/etc/passwd used to map uid numbers to user names
/vmunix system image
BUGS
The command name for swapped processes should be tracked down, but this
would make the program run slower.
As with ps(1), things can change while top is collecting information for
an update. The picture it gives is only a close approximation to
reality.
10/89 Page 3
TOP(1) UNIX System V(Local) TOP(1)
SEE ALSO
kill(1), ps(1), stty(1), mem(4), renice(8)
Page 4 10/89