csplit(1)                      DG/UX 5.4R3.00                      csplit(1)


NAME
       csplit - context split

SYNOPSIS
       csplit [-s] [-k] [ -f prefix ] file arg1 [... argn]

DESCRIPTION
       Csplit reads file and separates it into n+1 sections, defined by the
       arguments arg1...  argn.  By default the sections are placed in files
       labeled xx00 ...  xxn (n may not be greater than 99).  These sections
       get the following pieces of file:

             00:   From the start of file up to (but not including) the line
                   referenced by arg1.
             01:   From the line referenced by arg1 up to the line
                   referenced by arg2.
                   .
                   .
                   .
             n+1:  From the line referenced by argn to the end of file.

       If the file argument is a - then standard input is used.

       Options are:

             -s         Suppresses the printing of all character counts.
                        csplit normally prints the character counts for each
                        file created.

             -k         Leaves previously created files intact.  csplit
                        normally removes created files if an error occurs.

             -f prefix  The created files are named prefix00 ... prefixn.
                        The default is xx00 ...  xxn.

       The arguments (arg1 ...  argn) to csplit can be a combination of the
       following:

             /rexp/  Create a file for the section from the current line up
                     to (but not including) the line containing the regular
                     expression rexp.  The current line becomes the line
                     containing rexp.  This argument may be followed by an
                     optional + or - some number of lines (e.g., /Page/-5).

             %rexp%  The same as /rexp/, but no file is created for the
                     section.

             linenum Create a file from the current line up to (but not
                     including) linenum.  The current line becomes linenum.

             {num}   Repeat argument.  This argument may follow any of the
                     above arguments.  If it follows a rexp type argument,
                     that argument is applied num more times.  If it follows
                     linenum, the file will be split every linenum lines



Licensed material--property of copyright holder(s)                         1

csplit(1)                      DG/UX 5.4R3.00                      csplit(1)


                     (num times) from that point.

       Enclose all rexp type arguments that contain blanks or other
       characters meaningful to the shell in the appropriate quotes.
       Regular expressions may not contain embedded new lines.  csplit does
       not affect the original file.

   International Features
       csplit can process characters from supplementary code sets.  In
       regular expressions, searches are performed on characters, not bytes.

       Option:

       -fprefix
              Characters from supplementary code sets can be used for
              prefix.

EXAMPLES
           csplit -f cobol file '/procedure division/' /par5./ /par16./

       This example creates four files, cobol00 ... cobol03.  After editing
       the ``split'' files, they can be recombined as follows:

           cat cobol0[0-3] > file

       Note that this example overwrites the original file.

           csplit -k file  100  {99}

       This example would split the file at every 100 lines, up to 10,000
       lines.  The -k option retains the created files if there are less
       than 10,000 lines; however, an error message would still be printed.

           csplit -k prog.c  '%main(%'  '/^}/+1'  {20}

       Assuming that prog.c follows the normal C coding convention of ending
       routines with a } at the beginning of the line, this example will
       create a file containing each separate C routine (up to 21) in
       prog.c.

DIAGNOSTICS
       Self explanatory except for:

           arg - out of range

       This means that the given argument did not reference a line between
       the current position and the end of the file.

SEE ALSO
       ed(1), sh(1).
       regexp(5)






Licensed material--property of copyright holder(s)                         2