DISKLABEL(8) DISKLABEL(8)
NAME
disklabel - read and write disk pack label
SYNOPSIS
disklabel [ -r ] disk
disklabel -w [ -rs ] disk disktype [ packid [ priboot sec-
boot ] ]
disklabel -e [ -rs ] disk
disklabel -R [ -rs ] disk protofile [ priboot secboot ]
disklabel [ -NW ] disk
DESCRIPTION
Disklabel can be used to install, examine or modify the
label on a disk drive or pack. When writing the label, it
can be used to change the drive identification, the disk
partitions on the drive, or to replace a damaged label or
bootstrap. The disk label is located on one of the first
sectors of each disk (block 1 on BSD/386). On machines
that require a block-0 bootstrap (including AT-386), the
label is inserted into the bootstrap program. This infor-
mation is used by the system disk driver and by the boot-
strap program to determine how to program the drive.
There are several forms of the command that display,
install or modify the label on a disk. Each form has an
additional option, -r, which causes the label to be read
from or written to the disk directly, and installing a
bootstrap as well as a label when writing. This option
must be used when first installing a label on a disk in
order to install the boot blocks. When writing, the in-
core copy is also updated if possible. If the -s option
is specified with one of the commands that changes the
label, only the system's in-core label is modified. This
option allows label information to be set for a disk with
no on-disk label.
The first form of the command is used to examine the label
on the named disk drive (e.g. wd0 or /dev/rwd0c). It will
display all of the parameters associated with the drive
and its partition layout. Unless the -r flag is given,
the kernel's in-core copy of the label is displayed; if
the disk has no label, or the partition types on the disk
are incorrect, the kernel may have constructed or modified
the label. If the -r flag is given, the label from the
raw disk will be displayed rather than the in-core label.
The second form of the command, with the -w flag, is used
to write a standard label on the designated drive. The
required arguments to disklabel are the drive to be
labelled (e.g. wd0), and the drive type as described in
the disktab(5) file. The drive parameters and partitions
are taken from that file. If different disks of the same
physical type are to have different partitions, it will be
necessary to have separate disktab entries describing
each, or to edit the label after installation as described
June 24, 1990 1
DISKLABEL(8) DISKLABEL(8)
below. The first optional argument is a pack identifica-
tion string, up to 16 characters long. The pack id must
be quoted if it contains blanks. If the -r flag is given,
the disk sectors containing the label and bootstrap will
be written directly, otherwise the existing label will be
updated in place without modifying the bootstrap. If the
disk does not already have a label, the -r flag must be
used. In either case, the kernel's in-core label is
replaced.
Alternate versions of the bootstrap files may be specified
after the pack identifier. If an alternate bootstrap is
not specified, the standard bootstrap will be used. The
bootstrap programs are located in /usr/bootstraps. The
names of the bootstrap programs may be specified in disk-
tab(5); if not specified, the default names are of the
form basenameboot for the primary (block 0) bootstrap, and
bootbasename for the secondary (block 1-15) bootstrap; for
example, /usr/bootstraps/wdboot and /usr/bootstraps/bootwd
if the disk device is wd0.
An existing disk label may be edited by using the -e flag.
The label is read from the in-core kernel copy, or
directly from the disk if the -r flag is also given. The
label is formatted and then supplied to an editor for
changes. If no editor is specified in an EDITOR environ-
ment variable, vi(1) is used. When the editor terminates,
the formatted label is reread and used to rewrite the disk
label.
With the -R flag, disklabel is capable of restoring a disk
label that was formatted in a prior operation and saved in
an ascii file. The prototype file used to create the
label should be in the same format as that produced when
reading or editing a label. Comments are delimited by #
and newline. If the -r option is also given, a block-0
bootstrap is installed on machines that use one; either
the disktype or the names of the bootstrap files must be
specified on such machines.
Finally, the -NW flags for disklabel explicitly disallow
and allow, respectively, writing of the pack label area on
the selected disk.
FILES
/etc/disktab
/usr/bootstraps/xxboot
/usr/bootstraps/bootxx
SEE ALSO
disktab(5), disklabel(5)
DIAGNOSTICS
The kernel device drivers will not allow the size of a
June 24, 1990 2
DISKLABEL(8) DISKLABEL(8)
disk partition to be decreased or the offset of a parti-
tion to be changed while it is open. Some device drivers
create a label containing only a single large partition if
a disk is unlabeled; thus, the label must be written to
the ``a'' partition of the disk while it is open. This
sometimes requires the desired label to be set in two
steps, the first one creating at least one other parti-
tion, and the second setting the label on the new parti-
tion while shrinking the ``a'' partition.
BUGS
When a disk name is given without a full pathname, the
constructed device name uses the ``c'' partition on the
vax and the ``a'' partition on the tahoe.
June 24, 1990 3