NETSTAT(1) BSD Reference Manual NETSTAT(1)
NAME
netstat - show network status
SYNOPSIS
netstat [-Aan] [-f addressfamily] [system] [core]
netstat [-himnrs] [-f addressfamily] [-M core] [-N system]
netstat [-n] [-I [interface]] [-M core] [-N system] [-w wait]
netstat [-p protocol] [-M core] [-N system]
DESCRIPTION
The netstat command symbolically displays the contents of various net-
work-related data structures. There are a number of output formats, de-
pending on the options for the information presented. The first form of
the command displays a list of active sockets for each protocol. The
second form presents the contents of one of the other network data struc-
tures according to the option selected. Using the third form, with a
wait interval specified, netstat will continuously display the informa-
tion regarding packet traffic on the configured network interfaces. The
fourth form displays statistics about the named protocol.
The options have the following meaning:
-A With the default display, show the address of any protocol control
blocks associated with sockets; used for debugging.
-a With the default display, show the state of all sockets; normally
sockets used by server processes are not shown.
-d With either interface display (option -i or an interval, as de-
scribed below), show the number of dropped packets.
-h Show the state of the IMP host table.
-i Show the state of interfaces which have been auto-configured (in-
terfaces statically configured into a system, but not located at
boot time are not shown).
-I interface
Show information only about this interface; used with an wait in-
terval as described below.
-M Extract values associated with the name list from the specified
core instead of the default /dev/kmem.
-m Show statistics recorded by the memory management routines (the
network manages a private pool of memory buffers).
-N Extract the name list from the specified system instead of the de-
fault /vmunix.
-n Show network addresses as numbers (normally netstat interprets ad-
dresses and attempts to display them symbolically). This option
may be used with any of the display formats.
-p protocol
Show statistics about protocol, which is either a well-known name
for a protocol or an alias for it. Some protocol names and aliases
are listed in the file /etc/protocols. A null response typically
means that there are no interesting numbers to report. The program
will complain if protocol is unknown or if there is no statistics
routine for it.
-s Show per-protocol statistics.
-r Show the routing tables. When -s is also present, show routing
statistics instead.
-f addressfamily
Limit statistics or address control block reports to those of the
specified address family. The following address families are recog-
nized: inet, for AF_INET, ns, for AF_NS, and unix, for AF_UNIX.
The default display, for active sockets, shows the local and remote ad-
dresses, send and receive queue sizes (in bytes), protocol, and the in-
ternal state of the protocol. Address formats are of the form
``host.port'' or ``network.port'' if a socket's address specifies a net-
work but no specific host address. When known the host and network ad-
dresses are displayed symbolically according to the data bases /etc/hosts
and /etc/networks, respectively. If a symbolic name for an address is
unknown, or if the -n option is specified, the address is printed numeri-
cally, according to the address family. For more information regarding
the Internet ``dot format,'' refer to inet(3)). Unspecified, or ``wild-
card'', addresses and ports appear as ``*''.
The interface display provides a table of cumulative statistics regarding
packets transferred, errors, and collisions. The network addresses of
the interface and the maximum transmission unit (``mtu'') are also dis-
played.
The routing table display indicates the available routes and their sta-
tus. Each route consists of a destination host or network and a gateway
to use in forwarding packets. The flags field shows the state of the
route (``U'' if ``up''), whether the route is to a gateway (``G''),
whether the route was created dynamically by a redirect (``D''), and
whether the route has been modified by a redirect (``M''). Direct routes
are created for each interface attached to the local host; the gateway
field for such entries shows the address of the outgoing interface. The
refcnt field gives the current number of active uses of the route. Con-
nection oriented protocols normally hold on to a single route for the du-
ration of a connection while connectionless protocols obtain a route
while sending to the same destination. The use field provides a count of
the number of packets sent using that route. The interface entry indi-
cates the network interface utilized for the route.
When netstat is invoked with a wait interval argument, it displays a run-
ning count of statistics related to network interfaces. This display
consists of a column for the primary interface (the first interface found
during autoconfiguration) and a column summarizing information for all
interfaces. The primary interface may be replaced with another interface
with the -I option. The first line of each screen of information con-
tains a summary since the system was last rebooted. Subsequent lines of
output show values accumulated over the preceding interval.
SEE ALSO
iostat(1), nfsstat(1), ps(1), vmstat(1), hosts(5), networks(5),
protocols(5), services(5), trpt(8), trsp(8)
HISTORY
The netstat command appeared in 4.2BSD.
BUGS
The notion of errors is ill-defined.
Collisions mean something else for the IMP.
4.2 Berkeley Distribution March 27, 1993 2