delta(1) (Source Code Control System Utilities) delta(1)
NAME
delta - make a delta (change) to an SCCS file
SYNOPSIS
delta [-rSID] [-s] [-n] [-glist] [-m[mrlist]] [-y[comment]] [-p]
files
DESCRIPTION
delta is used to permanently introduce into the named SCCS file
changes that were made to the file retrieved by get -e (called the
g-file or generated file).
delta makes a delta to each named SCCS file. If a directory is
named, delta behaves as though each file in the directory were
specified as a named file, except that non-SCCS files (last component
of the path name does not begin with s.) and unreadable files are
silently ignored. If a name of - is given, the standard input is
read (see the NOTES section); each line of the standard input is
taken to be the name of an SCCS file to be processed.
delta may issue prompts on the standard output depending on certain
keyletters specified and flags [see admin(1)] that may be present in
the SCCS file (see -m and -y keyletters below).
Keyletter arguments apply independently to each named file.
-rSID Uniquely identifies which delta is to be made to
the SCCS file. The use of this keyletter is
necessary only if two or more outstanding gets
for editing (get -e) on the same SCCS file were
done by the same person (login name). The SID
value specified with the -r keyletter can be
either the SID specified on the get command line
or the SID to be made as reported by the get
command [see get(1)]. A diagnostic results if
the specified SID is ambiguous, or, if necessary
and omitted on the command line.
-s Suppresses the issue, on the standard output, of
the created delta's SID, as well as the number of
lines inserted, deleted and unchanged in the SCCS
file.
-n Specifies retention of the edited g-file
(normally removed at completion of delta
processing).
-glist Specify a list [see get(1) for the definition of
list] of deltas that are to be ignored when the
file is accessed at the change level (SID)
created by this delta.
7/91 Page 1
delta(1) (Source Code Control System Utilities) delta(1)
-m[mrlist] If the SCCS file has the v flag set [see
admin(1)] then a Modification Request (MR) number
must be supplied as the reason for creating the
new delta.
If -m is not used and the standard input is a
terminal, the prompt MRs? is issued on the
standard output before the standard input is
read; if the standard input is not a terminal, no
prompt is issued. The MRs? prompt always
precedes the comments? prompt (see -y
keyletter).
MRs in a list are separated by blanks and/or tab
characters. An unescaped new-line character
terminates the MR list.
Note that if the v flag has a value [see
admin(1)], it is taken to be the name of a
program (or shell procedure) that will validate
the correctness of the MR numbers. If a non-zero
exit status is returned from the MR number
validation program, delta terminates. (It is
assumed that the MR numbers were not all valid.)
-y[comment] Arbitrary text used to describe the reason for
making the delta. A null string is considered a
valid comment.
If -y is not specified and the standard input is
a terminal, the prompt comments? is issued on
the standard output before the standard input is
read; if the standard input is not a terminal, no
prompt is issued. An unescaped new-line
character terminates the comment text.
-p Causes delta to print (on the standard output)
the SCCS file differences before and after the
delta is applied in a diff(1) format.
FILES
g-file Existed before the execution of delta; removed after
completion of delta.
p-file Existed before the execution of delta; may exist
after completion of delta.
q-file Created during the execution of delta; removed after
completion of delta.
x-file Created during the execution of delta; renamed to
SCCS file after completion of delta.
Page 2 7/91
delta(1) (Source Code Control System Utilities) delta(1)
z-file Created during the execution of delta; removed during
the execution of delta.
d-file Created during the execution of delta; removed after
completion of delta.
bdiff Program to compute differences between the ``gotten''
file and the g-file.
EXAMPLE
The following example does a delta on file test1.c.
%delta s.test1.c
comments? second version
1.2
1 inserted
0 deleted
12 unchanged
NOTES
A get of many SCCS files, followed by a delta of those files, should
be avoided when the get generates a large amount of data. Instead,
multiple get/delta sequences should be used.
If the standard input (-) is specified on the delta command line, the
-m (if necessary) and -y keyletters must also be present. Omission
of these keyletters causes an error.
Comments are limited to text strings of at most 1024 characters.
Line lengths greater than 1000 characters cause undefined results.
SEE ALSO
admin(1), cdc(1), get(1), help(1), prs(1), rmdel(1), sccsfile(4).
bdiff(1) in the User's Reference Manual.
DIAGNOSTICS
Use help(1) for explanations.
7/91 Page 3