STTY(1) SysV STTY(1)
NAME
stty - set the options for a terminal
SYNOPSIS
stty [ -a ] [ -g ] [ options ]
DESCRIPTION
stty sets certain terminal I/O options for the device that is the current
standard input; without arguments, it reports the settings of certain
options.
In this report, if a character is preceded by a caret (^), then the value
of that option is the corresponding CTRL character (e.g., ``^h'' is
CTRL/h ; in this case, recall that CTRL/h is the same as the "back-space"
key.) The sequence ``^''' means that an option has a null value. This
has no effect on Apollo transcript pads. It is useful on dialup
terminals or VT100 windows. stty -a
-a reports all of the option settings;
-g reports current settings in a form that can be used as an argument
to another stty command.
Options in the last group are implemented using options in the previous
groups. Note that many combinations of options make no sense, but no
sanity checking is performed. The options are selected from the
following:
Control Modes
parenb (-parenb)
enable (disable) parity generation and detection.
parodd (-parodd)
select odd (even) parity.
cs5 cs6 cs7 cs8
select character size (see termio(7)).
0 hang up phone line immediately.
110 300 600 1200 1800 2400 4800 9600 19200 38400
Set terminal baud rate to the number given, if possible. (All
speeds are not supported by all hardware interfaces.)
hupcl (-hupcl)
hang up (do not hang up) Dataphone connection on last close.
hup (-hup)
same as hupcl (-hupcl).
cstopb (-cstopb)
use two (one) stop bits per character.
cread (-cread)
enable (disable) the receiver.
clocal (-clocal)
n assume a line without (with) modem control.
loblk (-loblk)
block (do not block) output from a non-current layer.
Input Modes
ignbrk (-ignbrk)
ignore (do not ignore) break on input.
brkint (-brkint)
signal (do not signal) INTR on break.
ignpar (-ignpar)
ignore (do not ignore) parity errors.
parmrk (-parmrk)
mark (do not mark) parity errors (see termio(7)).
inpck (-inpck)
enable (disable) input parity checking.
istrip (-istrip)
strip (do not strip) input characters to seven bits.
inlcr (-inlcr)
map (do not map) NL to CR on input.
igncr (-igncr)
ignore (do not ignore) CR on input.
icrnl (-icrnl)
map (do not map) CR to NL on input.
iuclc (-iuclc)
map (do not map) upper-case alphabetics to lower case on input.
ixon (-ixon)
enable (disable) START/STOP output control. Output is stopped
by sending an ASCII DC3 and started by sending an ASCII DC1.
ixany (-ixany)
allow any character (only DC1) to restart output.
ixoff (-ixoff)
request that the system send (not send) START/STOP characters
when the input queue is nearly empty/full.
Output Modes
opost (-opost)
post-process output (do not post-process output; ignore all
other output modes).
olcuc (-olcuc)
map (do not map) lower-case alphabetics to upper case on
output.
onlcr (-onlcr)
map (do not map) NL to CR-NL on output.
ocrnl (-ocrnl)
map (do not map) CR to NL on output.
onocr (-onocr)
do not (do) output CRs at column zero.
onlret (-onlret)
on the terminal NL performs (does not perform) the CR function.
ofill (-ofill)
use fill characters (use timing) for delays.
ofdel (-ofdel)
fill characters are DELs (NULs).
cr0 cr1 cr2 cr3
select style of delay for carriage returns (see termio(7)).
nl0 nl1 select style of delay for line-feeds (see termio(7)).
tab0 tab1 tab2 tab3
select style of delay for horizontal tabs (see termio(7)).
bs0 bs1 select style of delay for backspaces (see termio(7)).
ff0 ff1 select style of delay for form-feeds (see termio(7)).
vt0 vt1 select style of delay for vertical tabs (see termio(7)).
Local Modes
isig (-isig)
enable (disable) the checking of characters against the special
control characters INTR, QUIT, and SWTCH.
icanon (-icanon)
enable (disable) canonical input (ERASE and KILL processing).
xcase (-xcase)
canonical (unprocessed) upper/lower-case presentation.
echo (-echo)
echo back (do not echo back) every character typed.
echoe (-echoe)
echo (do not echo) ERASE character as a backspace-space-
backspace string. Note: this mode will erase the ERASEed
character on many CRT terminals; however, it does not keep
track of column position and, as a result, may be confusing on
escaped characters, tabs, and backspaces.
echok (-echok)
echo (do not echo) NL after KILL character.
lfkc (-lfkc)
the same as echok (-echok); obsolete.
echonl (-echonl)
echo (do not echo) NL.
noflsh (-noflsh)
disable (enable) flush after INTR, QUIT, or SWTCH.
stwrap (-stwrap)
disable (enable) truncation of lines longer than 79 characters
on a synchronous line. (Does not apply to the 3B2.)
stflush (-stflush)
enable (disable) flush on a synchronous line after every
write(2).(Doesnotapplyto
stappl (-stappl)
use application mode (use line mode) on a synchronous line.
(Does not apply to the 3B2.)
Control Assignments
control-character c
set control-character to c, where control-character is erase,
kill, intr, quit, swtch, eof, ctab, min, or time (ctab is used
with -stappl; min and time are used with -icanon; see
termio(7)). If c is preceded by an (escaped from the shell)
caret (^), then the value used is the corresponding CTRL
character (e.g., ``^d'' is a CTRL-d); ``^?'' is interpreted as
DEL and ``^-'' is interpreted as undefined.
line i set line discipline to i (0 < i < 127 ).
Combination Modes
evenp or parity
enable parenb and cs7.
oddp enable parenb, cs7, and parodd.
-parity, -evenp, or -oddp
disable parenb, and set cs8.
raw (-raw or cooked)
enable (disable) raw input and output (no ERASE, KILL, INTR,
QUIT, SWTCH, EOT, or output post processing).
nl (-nl) unset (set) icrnl, onlcr. In addition -nl unsets inlcr, igncr,
ocrnl, and onlret.
lcase (-lcase)
set (unset) xcase, iuclc, and olcuc.
LCASE (-LCASE)
same as lcase (-lcase).
tabs (-tabs or tab3)
preserve (expand to spaces) tabs when printing.
ek reset ERASE and KILL characters back to normal # and @.
sane resets all modes to some reasonable values.
term set all modes suitable for the terminal type term, where term
is one of tty33, tty37, vt05, tn300, ti700, or tek.
SEE ALSO
tabs(1).
ioctl(2) in the SysV Programmer's Reference.
termio(7).